Main Content

이 번역 페이지는 최신 내용을 담고 있지 않습니다. 최신 내용을 영문으로 보려면 여기를 클릭하십시오.

신호

신호 속성 구성 및 표시

신호는 시뮬레이션에서 두 블록 간에 데이터를 전송합니다. 데이터는 블록의 계산된 출력일 수도 있고, 단순히 메시지일 수도 있습니다. 신호의 값은 시뮬레이션 시간 동안의 모든 점에서 계산됩니다. 시뮬레이션 도중과 그 후에 신호 데이터 및 속성을 표시하거나, 블록 다이어그램에서 실시간 값을 확인하거나, 작업 공간에서 값을 변수로 기록할 수 있습니다. 또한, 추가 조사를 위해 신호를 파일 또는 작업 공간으로 내보낼 수도 있습니다.

숫자 데이터형, 초기값, 값 범위와 같은 신호 특성을 지정하여 모델의 수학적 동작을 제어할 수 있습니다.

블록

Signal SpecificationSpecify desired dimensions, sample time, data type, numeric type, and other attributes of signal
Bus to VectorConvert virtual bus to vector
IC신호 초기값 설정
ProbeOutput signal attributes, including width, dimensionality, sample time, and complex signal flag
Rate TransitionHandle transfer of data between blocks operating at different rates
Signal EditorDisplay, create, edit, and switch interchangeable scenarios
Signal ConversionConvert signal to new type without altering signal values
Weighted Sample TimeSupport calculations involving sample time
Width입력 벡터의 너비 출력

함수

disableimplicitsignalresolutionConvert model to use only explicit signal resolution
signalBuilderToSignalEditorImport signal data and properties from Signal Builder block to Signal Editor block
signalEditorStart Signal Editor
Simulink.SignalSpecify instance-specific properties of signal or discrete state
Simulink.ValueTypeSpecify properties of signals based on application-specific value types
sltraceTrace signals in a model
highlightHighlight tracing results
removehighlightRemove highlighted tracing results

클래스

sltrace.GraphProvide tracing information as graph for structure analysis

신호 속성View and edit signal properties
계측 속성View and edit logging and visualization properties for logged signal
속성 인스펙터Edit parameters and properties for any Simulink model element
모델 데이터 편집기Inspect and edit data items (signals, parameters, and states) in a table that you can sort, group, and filter

도움말 항목

신호 시작하기

  • Signal Basics
    Create, configure, identify, and test signals.
  • Signal Types
    Learn about different types of signals, such as control signals and composite signals.
  • Signal Groups
    Test or debug models by creating interchangeable groups of signal data.

신호 속성

신호 속성 표시하기

  • Highlight Signal Sources and Destinations
    Trace a signal to its source or destination while debugging or exploring a model.
  • Display Port Values for Debugging
    Display the values of block outputs on the block diagram during simulation.
  • Display Signal Attributes
    Improve model readability by displaying signal attributes, such as data types and dimensions, in the block diagram.
  • 신호 레이블 전파
    더욱 쉽게 신호를 식별하고 액세스할 수 있도록 신호에 이름을 지정합니다. 신호 레이블 전파를 활용하여 시스템 경계를 가로지르는 신호의 이름을 지정하는 수고를 줄이십시오.
  • Trace Connections Using Interface Display
    Display interfaces to trace signals through the nested levels, annotate signal characteristics, and view units associated with signals.

가변 크기 신호