Community Profile

photo

Manikandan


anna university

Last seen: 25일 전 |  2012년부터 활동

Followers: 0   Following: 0

연락

Professional Interests: Electric Drives

통계

All
  • Explorer
  • Personal Best Downloads Level 1
  • First Review
  • 5-Star Galaxy Level 2
  • First Submission
  • Revival Level 3
  • First Answer

배지 보기

Feeds

보기 기준

답변 있음
PI control techniques for speed control of a BLDC motor
Try to use trial and error method

대략 6년 전 | 0

답변 있음
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...

거의 8년 전 | 3

제출됨


Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in

대략 8년 전 | 다운로드 수: 3 |

Thumbnail

답변 있음
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...

대략 8년 전 | 0

답변 있음
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.

대략 8년 전 | 0

답변 있음
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in

대략 8년 전 | 0

답변 있음
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...

대략 8년 전 | 0

답변 있음
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...

대략 8년 전 | 0

답변 있음
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.

대략 8년 전 | 0

답변 있음
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in

8년 초과 전 | 1

답변 있음
how to find the setpoint ref input block in simlink for design of PI controller to control speed of servo motor... i can't find the setpoint bock in simulink.... setpoint ref input block...
use constant block

8년 초과 전 | 2

답변 있음
i want to control speed of DC motor using arduino via matlab.
use PWM

8년 초과 전 | 0

답변 있음
Single phaseInduction motor speed control
Your problem?

8년 초과 전 | 0

답변 있음
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in

8년 초과 전 | 1

답변 있음
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in

8년 초과 전 | 0

답변 있음
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]

8년 초과 전 | 0

답변 있음
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.

8년 초과 전 | 0

답변 있음
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.

8년 초과 전 | 0

답변 있음
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf

8년 초과 전 | 0

답변 있음
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.

8년 초과 전 | 0

답변 있음
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.

8년 초과 전 | 1

답변 있음
there is a built in model of brushless DC motor in simulink library. does anyone know the equations used for built in model of BLDC.
like it.

8년 초과 전 | 0

답변 있음
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...

8년 초과 전 | 0

답변 있음
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.

8년 초과 전 | 0

답변 있음
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in

8년 초과 전 | 0

답변 있음
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....

8년 초과 전 | 0

답변 있음
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...

8년 초과 전 | 0

답변 있음
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...

8년 초과 전 | 0

답변 있음
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...

8년 초과 전 | 0

답변 있음
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in

8년 초과 전 | 0

더 보기