Community Profile

photo

Martin

Last seen: 약 1달 전 2011 이후 활성

Statistics

All
  • Knowledgeable Level 3
  • Revival Level 3
  • 3 Month Streak
  • Knowledgeable Level 2
  • First Answer
  • Solver

배지보기

Content Feed

보기 기준

답변 있음
i want to learn about the oxygen concentrator example in simscape matlab ?
Hello Hassan, You can find information about it here: Oxygen Concentrator - MATLAB & Simulink (mathworks.com)

약 1년 전 | 0

답변 있음
Negative velocity curve from vehicle body block
Hi Vinay, It is difficult to say what happened, but it looks like recreating the subsystem worked. It may be possible that some...

약 1년 전 | 0

답변 있음
Source Code Condenser Code
Hi Rainer, A Condenser/Evaporator with two-phase fluid on one side and moist air on the other was introduced in R2019a. A Cond...

약 1년 전 | 0

답변 있음
Unexpected dog clutch disengagement behavior
Hello Frank, Thank you for including the example model to demonstrate the issue. The translational behavior of the shift link...

2년 이하 전 | 1

답변 있음
Unable to open the following model in R2019a trial version.
Hi Sadeer, It looks like the installation is not complete, or the path is incorrect. Definitely contact technical support for...

약 2년 전 | 0

답변 있음
Simple gear model with load dependent efficiency
Hi Mahesh, The load-dependent efficiency model assumes that torque loss is equal to a constant value plus an additional loss ...

약 2년 전 | 0

답변 있음
How is inertia in planetary gear block calculated?
Hello David, Yes, connecting the carrier port would be the carrier inertia. The planet inertia is the sum of all the planet g...

약 2년 전 | 0

답변 있음
I am getting the following error in simscape driveline please help
Hello Mastrieo, This could be due to an overconstrained model. Check to see if you have conflicting parts of the model, for e...

약 2년 전 | 0

답변 있음
Thermal behaviour of Harmonic Drive Simulink
Hello Kotryna, Some of this may have been addressed in your other questions. I would also check the Solver Configuration bloc...

약 2년 전 | 0

답변 있음
Can't find 'Drive Cycle Source' blockset in Simcsape/Simulink.
Hello Rohan, The Drive Cycle Source is part of the Powertrain Blockset. Check to see if you have that product installed. M...

약 2년 전 | 0

| 수락됨

답변 있음
"First solve for initial conditions failed to converge." Thermal model
Hello Kotryna, The temperature on those blocks is a difference, not absolute. Also focus on specifying the differential varia...

약 2년 전 | 0

답변 있음
Initial temperature harmonic drive gear
Hi Kotryana, As a first step, I would look at the Variable Viewer to see what is met and what is not. In the toolstrip, selec...

약 2년 전 | 0

답변 있음
Generic engine oscillating output
Hi Stephen, This looks like the oscillation is due to the interactions between the slipping pullies in the two belt drives. I...

약 2년 전 | 0

답변 있음
Quarter model with tire (Magic Formula) SimScape Driveline
Hello Marcin, The H port is a translational conserving port associated with the hub of the tire. It should be associated with...

약 2년 전 | 0

| 수락됨

답변 있음
Is it usually used Simscape Driveline for designing the powertrain of a diesel-electric locomotive? Are there any examples about trains?
Hello Stefania, While we do not have any shipping examples regarding trains, users have successfully used Simscape Driveline ...

약 2년 전 | 0

답변 있음
How can i see the output torque of a gearbox
Hello Sree, If you need the value during simulation, you could add a Torque Sensor from the Simscape Foundation Library in se...

약 2년 전 | 0

답변 있음
Looking for Leadscrew model in library and not found.
Hello Orlando, Do you have Simscape Driveline installed? This block is in the Simscape Driveline library under Gears and Rota...

약 2년 전 | 0

| 수락됨

답변 있음
Torque vector must be arranged in strictly ascending order.
The block is not erroring because of the torque vector given on the Engine Torque tab. Speed is the independent vector that must...

2년 이상 전 | 0

답변 있음
Disk Friction Clutch - OPEN clutch
Hello Berkan, There are two types of kinetic friction in the model. The kinetic friction of the clutch plates pushing against...

2년 이상 전 | 0

답변 있음
Is it possible to debug .ssc of simscape while simulation is running?
Hello Omprakash, I key distinction with Simscape is that it uses acausal modeling. This means that the equations written in a...

약 3년 전 | 1

답변 있음
can Simscape two phase flow components deal with air / water mixtures?
Hi Xilin, You can try to use the Moist Air domain. This domain is nominally set with dry air, water vapor, and a trace gas. T...

약 3년 전 | 0

답변 있음
Error with Magic Tire formula from Simscape Driveline " Nonlinear Solver:"
Hi Gary, My intuition says that once the torque breaks the friction, there is nothing to stop the tire from spinning freely. ...

약 3년 전 | 0

답변 있음
variable nonlinear spring & damper
Hello Harsh, They are in Simscape Driveline. Go to Couplings & Drives, then Springs & Dampers. There you will find nonlinear,...

약 3년 전 | 0

답변 있음
what unit does simscape engine fuel consumption output
Hello Angus, The FC port outputs the fuel consumption rate in kg/s. Martin

약 3년 전 | 0

답변 있음
Simscape- Moist air error. Temperature at port B must be less than or equal to Maximum valid temperature.
Hello Sachin, One possibility is that the constant flow rate is causing a pressure rise in the Constant Volume Chamber. As th...

3년 이상 전 | 0

답변 있음
Why does my acceleration signal from simscape looks so weird?
Hi Rik, Numerical derivatives are inherently noisy, and subject to spikes due to time step differences, jumps in the solution...

3년 이상 전 | 0

| 수락됨

답변 있음
PS Divide, Accelaration, Feedback
Hello Vitali, It is possible that the rotational motion sensor is giving a value of 0 to the PS Divide block. Have you set th...

3년 이상 전 | 0

답변 있음
Generic engine won't start with new parameters
Hello Sandeep, The engine is may not be producing torque as it may have stalled. Just as with a real engine, when the speed is ...

4년 이하 전 | 0

| 수락됨

답변 있음
Simscape driveline piston model
Hello Matthew, You could consider taking a look at sdl_engine_testbed. It has three Piston Engine blocks. When the Piston Engin...

4년 이하 전 | 0

| 수락됨

답변 있음
how to control variable ratio gearbox \\ need gear ratio to be changed continuously as per requirement \\ i use student version of matlab and have simscape driveline
Hello Vaibnhav, The Variable Ratio Transmission in the Couplings sublibrary of Simscape Driveline might meet this need.

4년 이하 전 | 0

더로드