photo

Ankur Bose

Last seen: 2일 전 2017년부터 활동

Followers: 0   Following: 0

메시지

통계학

  • Knowledgeable Level 4
  • First Submission
  • GitHub Submissions Level 1
  • 6 Month Streak
  • Revival Level 2
  • First Review
  • First Answer

배지 보기

Feeds

보기 기준

답변 있음
Example model overflows board's flash memory, which is the same reported to be used in the example
Can you try using the cubepilot_cubeorange_multicopter build configuration in hardware setup screens instead of the default one?...

대략 1개월 전 | 1

답변 있음
PX4 HITL simulation timing synch (lockstep) issue
PX4 HITL simulations are not lockstep. Since lockstep simulations are not real time, making HITL simulations lockstep would defe...

대략 1개월 전 | 1

| 수락됨

답변 있음
Unable to access Model Configuration Parameters for PX4 Flight Controller
Please install the UAV Toolbox Support Package for PX4 Autopilots from the add-on manager

3개월 전 | 0

답변 있음
I am implementing the px4demo_attitudeSystem demo on a hexacopter, but I am encountering the following error
The Simulink model 'px4demo_attitudeSystem' contains a model reference 'px4demo_attitude_control'. Open that model (by doing rig...

3개월 전 | 0

답변 있음
UAV toolbox support package for PX4 - Design Path Follower Algorithm Example
There is no example available for "Path follower algorithm" workflow in the UAV Toolbox Support Package for PX4 Autopilots

3개월 전 | 0

답변 있음
Compatibility of Pixhawk 2.4.8 with UAV toolbox for PX4
As of R2024a, the UAV Toolbox support package for PX4 autopilots supports PX4 version 1.14. With this firmware version, it is re...

3개월 전 | 0

답변 있음
UAV Toolbox px4 demo host target with Simulink Plant - SITL simulation result question
In the MIL simulation, only the controller is involved. However, when the SITL simulation is run, all of the PX4 modules apart f...

6개월 전 | 1

답변 있음
Obtain msg from Pixhawk
In you MATLAB script, add the below two lines of code dialect = mavlinkdialect("common.xml"); msg = deserializemsg(dialect,buf...

7개월 전 | 1

| 수락됨

답변 있음
The PX4 firmware build fails consistently for SITL
Can you try reinstalling the Cygwin toolchain?

7개월 전 | 0

답변 있음
not able to verify the installation in setup cygwin toolchain and download px4 source code in UAV toolbox support package for px4 autopilot
We need some more details on the issue. Reach out to MathWorks Tech support

7개월 전 | 0

| 수락됨

답변 있음
How to use the block "To file" or "To workspace" in PX4 SITL with jmavsim
The use of "To File" or "To workspace" block in SITL mode is not supported. For logging, you need to use Monitor & Tune

7개월 전 | 0

| 수락됨

답변 있음
PX4 UAV Toolbox px4demo_attitudeSystem Attitude Controller for a Hexacopter
What does the status output of the RC block indicate?

7개월 전 | 0

답변 있음
Error when run example "Px4DemoHostTargetWithSimulinkPlantStart"
Are you trying to generate code for the plant model? The plant model is supposed to run on the host (by clicking run in Simulink...

7개월 전 | 0

답변 있음
Error in PX4 Firmware Build
Can you try to build the CMake for px4_fmu-v3_default?

7개월 전 | 0

답변 있음
PX4 HIL with Simulink plant: which COM port to select?
You should select COM3.

7개월 전 | 0

| 수락됨

답변 있음
How can I read signal when I build a controller on PX4 host target(SITL) after the simulation in jMAVsim?
At the moment, the PX4 uLog block does not support logging in SITL mode. For logging for Host Target, select the logging option ...

7개월 전 | 0

| 수락됨

답변 있음
PX4 toolbox error: build,deploy on run on Pixhawk 6x
We are looking into this issue. Set the following preference in your MATLAB command window and try building the model again

7개월 전 | 0

| 수락됨

답변 있음
PX4 HIL with Pixhawk 6x : HIL with simulink plant dynamics using Sik Telemetry Radio. Could not connect to target application: XCP serial port error
Note that from MATLAB & Simulink, the Wireless Monitor & Tune workflow has not been tested. This workflow sometimes works, but ...

7개월 전 | 0

| 수락됨

답변 있음
Code generation information file does not exist while building px4 firmware
Can you change the directory where you are changing the code? The length of the current path is too long and Windows has a limit...

7개월 전 | 0

답변 있음
PX4 SITL with simulink based plant model, system not found
Thanks for reporting this issue. This a bug and we are working to push the fix out. I am attaching 3 MATLAB scripts in this answ...

8개월 전 | 0

| 수락됨

답변 있음
PX4 HIL with Pixhawk 6x : HIL with simulink plant dynamics using Sik Telemetry Radio
The COM port should be one over which you want to communication between plant and Autopilot to happen. If you want the MAVLink d...

8개월 전 | 0

| 수락됨

답변 있음
Upload custom flight controller on Pixhawk 4, and flight tests
Check if the board is in HITL mode. In HITL mode, the actuator pins are disabled. If you want to run the engines, then you have ...

9개월 전 | 0

| 수락됨

답변 있음
PX4 toolbox in Simulink:when performing SITL with Jmavsim error code -10
This error indicates there might be data drop while sending data between Host Target and Simulink in External Mode. But External...

10개월 전 | 0

| 수락됨

답변 있음
Why am I receiving "fatal error: algorithm: No such file or directory" from the MAVLink Serializer block during Build & Deploy on a Pixhawk 1?
The MAVLink blocks in Simulink can only be deployed on a Linux target as mentioned here. The Pixhawk board does not rub Linu...

10개월 전 | 1

| 수락됨

답변 있음
UAV Toolbox Support Package Alternative?
We are currently working on supporting PX4 1.14 in UAV Toolbox support package for PX4 Autopilots. We will let you know when the...

11개월 전 | 0

답변 있음
QGroundControl doesn't recognize Pixhawk 6x
In HITL mode, the Pixhawk 6x is not supposed to connect directly to QGroundcontrol but via the MAVLink bridge in the Simulink pl...

11개월 전 | 1

답변 있음
Why the PX4 firmware version supported by the Pixhawk 6x (minimum version 1.13.1) and the firmware version supported by the UAV Toolbox Support Package for PX4 Autopilots (ver
The support for Pixhawk 6x is available in PX4 Firmware v1.12.3. Can you elaborate on what do you mean by COM port disappears? W...

11개월 전 | 0

답변 있음
Pixhawk 6X / 5X / 6C support by Simulink
Pixhawk 6x is now a supported targe in R2023a version of MATLAB in the latest release of UAV Toolbox support ackage for PX4 Auto...

11개월 전 | 0

답변 있음
Store data using the "To File" or " to workspace" block when using the PX4 toolbox on Simulink performing code generation
Logging data using To workspace block is only supported when you deploy to Pixhawk hardware. In SITL or PX4 Host Target, To work...

12개월 전 | 0

| 수락됨

답변 있음
Can I use Pixhawk6C instead of Pixhawk4 when using UAV toolbox support packages for PX4 autopilots?
We are currently working on developing support for Pixhawk 6c. BTW, we don have support for Pixhawk 6x board in R2023a. So if yo...

12개월 전 | 0

더 보기