Feeds
질문
How do I use Simulink Coder to build a Simulink model and generate the necessary header files that seem to be missing?
Hello, I’m trying to build a simple LQR block diagram using Simulink Coder for deployment on a Raspberry Pi board. However, du...
5개월 전 | 답변 수: 1 | 0
1
답변질문
How to implement an LQR controller when the system's state variables and control inputs have different units?
Hello, I am wondering how to implement an LQR controller when the state variables and control inputs have different units. For...
11개월 전 | 답변 수: 1 | 0
1
답변질문
How to implement MPC when the number of states is greater than the number of outputs?
I want to implement MPC using MATLAB's Model Predictive Control Toolbox. When I checked the official MATLAB website, I found on...
11개월 전 | 답변 수: 1 | 0
1
답변답변 있음
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I have another problem, that is QGroundControl doesn't recognize a pixhawk board when px4 firmware was built from MATL...
11개월 전 | 0
답변 있음
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...
How to troubleshoot pixhawk build error problem during executing example file?
I just fixed this problem by installing PX4-Autopilot firmware to the Linux home directory(not windows directory) and not execut...
12개월 전 | 1
질문
How to troubleshoot pixhawk build error problem during executing example file?
Hello, I want to execute the example of Send and Receive Serial Data Using PX4 Autopilots Support Package. I followed the step...
12개월 전 | 답변 수: 2 | 0
2
답변질문
How can I execute a Simulink block only when a specific condition is met?
Hi all, Is there a way to execute the following block diagram only when a certain condition is satisfied (e.g., when a joysti...
대략 1년 전 | 답변 수: 1 | 0
1
답변질문
How to use "StabilityThreshold" estimation option in greyest function?
Hello, To predict the lateral equations of the H4 Hercules using a greybox model, I defined the model function as follows and s...
대략 1년 전 | 답변 수: 1 | 0
1
답변질문
Problem Occurred While Using MATLAB System Identification Toolbox
Hello, I am currently performing system identification using the System Identification Toolbox after extracting the response dat...
대략 1년 전 | 답변 수: 1 | 0
1
답변질문
Inquiry about IP address and port number for UDP Send and UDP Receive block
Hello all, I have a question about the IP addresses and port numbers for the UDP Send and UDP Receive blocks. When sending and ...
1년 초과 전 | 답변 수: 1 | 0
1
답변질문
How to store object(like udp object) in level-2 s-function?
Hello all, I want to send control input from Matlab to FlightGear and receive aircraft data from FlightGear to Matlab with UDP ...
1년 초과 전 | 답변 수: 1 | 0
1
답변질문
How to calculate minimum singular value of I+L and I+inv(L) for MIMO system?
Hello, I want to calculate minimum singular value for MIMO system, and here is an example %% A = [0.1873 0.8403 -0.6003 -2.1...
거의 2년 전 | 답변 수: 1 | 0
1
답변질문
What's the difference between two command?
Hello, In general, the command of nyquist plot is nyquist(sys,omega), but an example of textbook the command of nyquist is nyqu...
거의 2년 전 | 답변 수: 1 | 0
1
답변Discussion
How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...
대략 2년 전 | 0
질문
How to maintain eigenvalues sequence
Hello, I have to draw root-locus for longitudinal motion; Short Period Mode and Phugoid Mode. Here is a code %% Dynamics Vp =...
대략 2년 전 | 답변 수: 0 | 0
