Community Profile

photo

Noor Amira Ilyanie


Last seen: 4일 전 |  2022년부터 활동

통계

  • Thankful Level 2
  • First Answer

배지 보기

Content Feed

보기 기준

질문


What solver need to be used to run the simscape model?

4일 전 | 답변 수: 1 | 0

1

답변

질문


How to get 1 output from 2 input using lookup table?
I have set the table data, breakpoints 1 and 2 using my value. But, I keep getting this error.

25일 전 | 답변 수: 0 | 0

0

답변

질문


How do I convert the codings in Arduino IDE software into the S function simulink block?
I have the codings in Arduino software, but dont know how to interpret exactly the same in simulink s-function.

대략 2개월 전 | 답변 수: 1 | 0

1

답변

질문


Load Arduino Files (coding) in Matlab Command Window
I have my coding in forms of arduino (.ino). I need to call or load the files in matlab command window. How can i load the ardui...

대략 2개월 전 | 답변 수: 1 | 0

1

답변

질문


what block in simulink can be used for remote control flysky?
I try using pwm block to control the dc motor. but it turns out different rotation. i have checked all my connection.

2개월 전 | 답변 수: 1 | 0

1

답변

질문


Why do the DC motor with the same PWM block in Arduino giving an output of different direction of motor rotation
I have set both dc motor the same value of pwm, but i kept getting the output different in terms of rotation of the motor. how...

2개월 전 | 답변 수: 0 | 0

0

답변

질문


coding for mapping rc values to pwm values using simulink block diagram
I had coded the programs in Arduino IDE software, but now I need to program the same thing in Simulink Matlab. I had stuck on ho...

3개월 전 | 답변 수: 1 | 0

1

답변

질문


When I run the simulation, I am facing this problem.
Build process completed successfully Saving external mode simulation output as a single object is not supported because the wor...

9개월 전 | 답변 수: 1 | 0

1

답변

질문


Simulation on MPU6050 Accelerometer using simulink block. Why I end up getting the data start from zero for acceleration z-axis when I include the filter?
This is my simulink model. I observed that my data when i run the simulation it start from zero. It should start within 9.81 val...

9개월 전 | 답변 수: 0 | 0

0

답변

질문


WHY IS IT WHEN I RUN THE MODEL, IT IS INVALID AND SHOW ERROR.
I keep getting this error when i run the model "Error in port widths or dimensions. 'Output Port 1' of 'dcmotornew260822/MPU6050...

9개월 전 | 답변 수: 1 | 0

1

답변

질문


mpu6050 calibrations, offset of the mpu6050 and filtering noise.
I got the raw data from the accelerometer mpu6050 in simulink matlab. the blue data is x, red is for y and orange is for z axis ...

9개월 전 | 답변 수: 1 | 0

1

답변

질문


Problem in getting the data stored to SD card after running the hardware test using Arduino mega that are attached with mpu6050 accelerometer and also SD card.
I have the simulink model of dc motor that are connected to arduino with the attachment of mpu6050 accelerometer and also sd car...

9개월 전 | 답변 수: 1 | 0

1

답변

질문


Why do I keep received failed to generate binary output error?

9개월 전 | 답변 수: 1 | 0

1

답변

질문


How to get acceleration data in Simulink through scope or workspace? How should i know whether the acceleration data is from two of the dc motor?

10개월 전 | 답변 수: 0 | 0

0

답변

질문


for the reading pwm, what is the unit of the 200 in the block? because it can be tune more than 255.

10개월 전 | 답변 수: 1 | 0

1

답변

답변 있음
DC Motor Position Control using Potentiometer as a Feedback
what is 0 to 255 unit? is it voltage or rpm? or bit?

10개월 전 | 0

질문


Can I read voltage and current measurement from simulink model that containts a model of connections in Arduino Uno?
I had done the connections on simulink for the attachment of the pins in Arduino to the dc motor. But i dont know how to take th...

10개월 전 | 답변 수: 1 | 0

1

답변