photo

saleh shlimet


Last seen: 3개월 전 |  2020년부터 활동

Followers: 0   Following: 0

통계

  • Thankful Level 2

배지 보기

Feeds

보기 기준

질문


How can I obtain the difference between two data stored in workspace?
I experimentally tested a motor and the measured speed and the reference speed were stored in the workspace. My supervisor aske...

대략 1년 전 | 답변 수: 1 | 0

1

답변

질문


How to execute the same code for a specific time?
I want to estimate the shaft speed of a motor and to do that I obtain the speed error between the reference speed and the estima...

대략 2년 전 | 답변 수: 1 | 0

1

답변

질문


Position error of motor shaft
I want to obtain the position error of motor shaft so I subtracted the estimated position from the measured position. modulus f...

대략 2년 전 | 답변 수: 1 | 0

1

답변

질문


how to export varied variable to saturation block in Simulink?
I tried to use varied value in the Saturation block and this value (called flux) exported from the output of a lookup table? I u...

대략 2년 전 | 답변 수: 1 | 0

1

답변

질문


Use a command only once
I use a code to search for an accurate rotor position. I used an initial value for the position (theta_b=0) as shown below and t...

2년 초과 전 | 답변 수: 2 | 0

2

답변

질문


Code error in MATLAB function block.
I wrote a code in a MATLAB function block that consists of two inputs one input for the signal that needs to be filtered and the...

거의 3년 전 | 답변 수: 1 | 0

1

답변

질문


Calculate cycle time for a signal by code
I want to calculate the cycle time for a signal (the frequency) by using a code (Matlab function block). For examble, in a motor...

대략 3년 전 | 답변 수: 0 | 0

0

답변

질문


Why the amplitude of the 90 shifted phase signal when use the analytic signal block is not equal to the original signal?
I could manage to shift the phase of signal by 90 by using analytic signal block. But, the problem is that its amplitude is not ...

4년 초과 전 | 답변 수: 1 | 0

1

답변

질문


how to shift phase of unknown frequency signal by 90 by using hilbert transform?
I tried to shift an unknown frequency signal by 90 by applying hilbert transform comand (imag(hilbert(x)) in matlab function blo...

4년 초과 전 | 답변 수: 0 | 0

0

답변

질문


How to connect simulink blocks with RF blocks (interface)?
I tried to use simulink blocks with RF blocksets but they can not be connected to each other. I think there is an interface betw...

4년 초과 전 | 답변 수: 1 | 0

1

답변

질문


How to shift a signal in simulink by 90 degrees?
I want to shift a signal by 90 degrees. there is a block called phase shift in RF blockset, but it cannot be used with simulink....

4년 초과 전 | 답변 수: 1 | 0

1

답변

질문


A problem with the solver
A problem with the solver when I run a model. when I disconnect the gate driver (simulink) from the inverter (simcap) the proble...

4년 초과 전 | 답변 수: 1 | 0

1

답변

질문


measuring the phase to neutral voltage in PMSM
in the MATLAB, how can I measure the voltage between the phase and the neutral point in the PMSM machine? (there is no access to...

대략 5년 전 | 답변 수: 1 | 0

1

답변