How to solve algebraic loop error??
조회 수: 363 (최근 30일)
이전 댓글 표시
Hii....I came across this error while making a model..
Simulink cannot solve the algebraic loop containing 'trial_3/PV panel/PV module' at time 0.0 using the TrustRegion-based algorithm due to one of the following reasons: the model is ill-defined i.e., the system equations do not have a solution; or the nonlinear equation solver failed to converge due to numerical issues. To rule out solver convergence as the cause of this error, either a) switch to LineSearch-based algorithm using set_param('trial_3','AlgebraicLoopSolver','LineSearch') b) reducing the VariableStepDiscrete solver RelTol parameter so that the solver takes smaller time steps. If the error persists in spite of the above changes, then the model is likely ill-defined and requires modification.
I am using coding to make photovoltaic panel and MPPT P&O algorithm.
Please help me to solve this error.
댓글 수: 4
Jim Riggs
2019년 12월 2일
It's true that you can break algebraic loops using a unit delay as Azzi Abdelmalek says, but judging by the comments, people are not reviewing the link provided by Walter Roberson, below. This article contains some important information and considerations on the effect of using a unit delay and provides an alternative solution.
Malaiyappan M
2020년 8월 17일
in MPPT Buck/Boost Converer try adjust the Inductor Value to resolve this error
채택된 답변
Azzi Abdelmalek
2012년 11월 23일
편집: Azzi Abdelmalek
2012년 11월 23일
Algebraic loop occurs often, when you have a feedback through a constant block or equivalent, which means your signal y(t0)=constant * y(t0) , you should have y(t0+1)=constant*y(t0) which you can get with a unit delay block
댓글 수: 15
NING XUE
2020년 3월 10일
Simulink cannot solve the algebraic loop containing 'partial_shading_conditions2/PV_SERIES2/Subsystem/Divide2' at time 0.039814999999999996 using the LineSearch-based algorithm due to one of the following reasons: the model is ill-defined i.e., the system equations do not have a solution; or the nonlinear equation solver failed to converge due to numerical issues. To rule out solver convergence as the cause of this error, either a) switch to TrustRegion-based algorithm using set_param('partial_shading_conditions2','AlgebraicLoopSolver','TrustRegion') b) reducing the VariableStepDiscrete solver RelTol parameter so that the solver takes smaller time steps. If the error persists in spite of the above changes, then the model is likely ill-defined and requires modification.
The same issue,but I have place the unit delay before the feedback,can't solve this problem
can you help me?
추가 답변 (5개)
Ahmed
2019년 6월 19일
I've faced the same problem before, it can be solved by adding a unit delay block and type "set_param('trial_3','AlgebraicLoopSolver','LineSearch') " in the command prombit window of MATLAB.
댓글 수: 2
Akash maheshwari
2019년 10월 3일
can you pleasse explain set_param('trial_3','AlgebraicLoopSolver','LineSearch'). i did that in my matlab command window but window show me that algebraic loop parameter did not found.
Gert Kruger
2019년 6월 27일
PV panel model with fixed algebraic loop: https://www.mathworks.com/matlabcentral/fileexchange/71682-pv-array-with-algebraic-loop-broken
댓글 수: 2
ayachi amor
2021년 6월 14일
Click on the PV panel itself, go to ' Advanced', then click on 'Break algebaic loop in internal model'.
hope to be solved.
댓글 수: 1
Zachary Naidoo
2022년 4월 14일
Hi, I have tried this by my displays for voltage and current show nan when for this. However if I don't click it then it displays the result with an error
참고 항목
카테고리
Help Center 및 File Exchange에서 Classical Control Design에 대해 자세히 알아보기
제품
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!