Data acquistion with Simulink 2012b and Arduino UNO

조회 수: 6 (최근 30일)
Rodolfo Buschle
Rodolfo Buschle 2012년 9월 29일
댓글: SHARIQ SHAMSI 2017년 3월 26일
Hello everyone,
I've been trying to read data from my arduino UNO on simulink with no success.
I connected a potentiometer on analog port 3 (A3) on the arduino. On simulink I have an Analog Input block connected to a scope block.
I run on target and then play the simulation, but I only read 0 on the scope.
To be honest, I'm pretty confused. The help files were not really helpful and I have tried every possible combinations of blocks. Maybe it's best using a Serial Receive block?!
By the way, I'm quite new to Simulink.
Any help will be greatly appreciated, as I need to get this working for my project.
  댓글 수: 5
Md Rasheduzzaman
Md Rasheduzzaman 2015년 10월 21일
Ardunio Uno does not support signals to show up on scopes. Buy Arduino mega.
SHARIQ SHAMSI 2017년 3월 26일
Mr. Rasheduzzaman, you mean the same model will work with mega and produce the same result?

댓글을 달려면 로그인하십시오.

답변 (12개)

Ryan G
Ryan G 2012년 10월 1일
Make sure you have the right pin selected in the input block. When you play the model, set it to run 'inf' so you can play around with your board and Simulink will keep running.
Are you sure you're setup to run on the arduino board? In the configuration parameters there is a 'Run on Target Hardware' section. You can select the Arduino Uno from here.
How are you running the model? Try tools -> run on target hardware -> run.

Rodolfo Buschle
Rodolfo Buschle 2012년 10월 1일
편집: Rodolfo Buschle 2012년 10월 1일
Hello Ryan,
Thanks for your answer.
First of all, I should point out my specs: I'm running a Windows 7 x64 Professional, Core i7 720QM, 8gb Dual-Channel DDR3, nVidia Quadro FX 880m, Matlab 2012b (Arduino support package installed through MATLAB target installer). Everything is up-to-date.
Here's a walk through of what I'm doing: 1) Start a new model; 2) Insert a Analog Input block (Set pin to 0 and sample time to 0.1); 3) Insert a scope block and connect to the Analog Input block; 4) Set the simulation time to "inf"; 5) Tools > Run on Target Hardware > Prepare to Run...; 6) Set target hardware to Arduino UNO; 7) Set host COM port: to COM5 (tested on the arduino IDE to make sure it's the right port, and it is.); 8) Apply and close prepare to run window; 9) Tools > Run on Target Hardware > Run...; ("Model successfully downloaded to 'Arduino UNO'); (In my understanding the Tx LED on the Arduino should be blinking, but isn't) 10) Run simulate and get nothing but zero's on the scope;
I have checked the circuit, and it works just fine on the Arduino IDE. It must be a detail that I'm missing, but frankly, I have no idea how to make it work.
I thought maybe I could run it on External mode, but I have an Arduino UNO and the external mode only runs on the Arduino MEGA.
I tried running through YouTube and the MATLAB community but I couldn't see a single video or post about someone running a model on the Arduino and viewing the results on simulink.
I kind of managed to make it run, by making one model with Analog input connected to Serial Transmit and download it to the Arduino. Then, on a new block a set a Serial receive block connected to a scope (I also set a Serial Configuration block, both found on the Instrument Control Toolbox) a run a simulation with 'inf'. It kind of works, but very sluggish, and I'm not satisfied with that solution.
Anyway, any help will be greatly appreciated.
To format of the text isn't coming as I wrote it, but I guess you can read it, sorry for that.
  댓글 수: 1
Ryan G
Ryan G 2012년 10월 1일
"I connected a potentiometer on analog port 3 "
When you wrote that in the main post I read it as 'pin' 3, is this the case? Try stting the Input block to 3 instead of 0. Essentially it is trying to read whatever is at pin 0, which at this point there does not seem to be anything on that pin.
I just went to the product page and think I found the main problem.
"Interactive parameter tuning and signal monitoring of applications running on the Arduino Mega (not available on Arduino Uno)"
"Model deployment for stand-alone operation"
Essentially your model is 'deploying' on the target. This means there is not really any more interaction with Simulink. You could start the Arduino running and unplug it from the PC. However, if you do want to monitor it you can either use MATLAB or Simulink to read from the serial port in the PC (which it sounds like you've found is slow).
The Ardunio Input block in this case is simply used in whatever type of design you are planning in Simulink (like a feedback control).

댓글을 달려면 로그인하십시오.

YT 2013년 1월 23일
Have you solved the problem? I have the same issue. The sensor works very well at Arduino IDE. I also detects voltage change at the pin using a multimeter. But i cannot make it work at Simulink. I tried Rodolfo's way of using the serial port receive/send, it did not work either. I use win7 64bit + Matlab 2012a. Any suggestions?

Robalivry 2013년 2월 14일
What did you do exactly to read with Simulink ?
For my part, I always :
* make a new variable with my Arduino in command line :
>> Due = arduino('COM4');
(I use a Duemilanove)
* go to Simulink, put a scope in my model and link it to the Analog Input found in the ArduinoIO library AND put a Setup block (found at the same place) in the model
* Double-click on the setup block and chose "existing variable #1" (or something like this) and enter the name of my variable "Due" in the field below.
* Then go to the Analog Input block and chose the *same* "existing variable #1".
* Run my model and it works.
Hope that will help !

shri raje
shri raje 2013년 3월 5일
Can anybody will give me pictorial representation of communicating virtual com port with proteus and simulink(2012a) for detecting analog signal and displaying it on scope of simulink(2012a)???????????????

Joaquin 2013년 7월 17일
Rodolfo, Can you solve your problem with data acquisition?

Kashyap 2013년 11월 17일
Could anyone solve the problem with data acquisition using Arduino uno and simulink?? Any help would we greatly appreciated.
Thank You.

William sanchez
William sanchez 2014년 5월 27일
Any help us please! i have the same problema with arduino uno and preset.

Valmir Sadiku
Valmir Sadiku 2014년 5월 27일
편집: Valmir Sadiku 2014년 5월 27일
I tried two years ago and it worked for me fine. The attached picture shows you, how you can build a simple analog read from arduino into simulink.
First model read the analog sensor (in my an poti) and write it to the serial com port (byte by byte). this model must be uploaded to the arduino!
The second model reads the serial port as shown in this picture.
hope this will help you!
  댓글 수: 4
Munther Sharaiha
Munther Sharaiha 2015년 3월 8일
it keeps saying data mismatch
OJIJ 2016년 1월 12일
편집: OJIJ 2016년 1월 12일
thank's for your answer. I success to analogread with (Arduino Uno) using your idea (conversion to the serial) but I used another configuration instead your first model as you are shown in this picture:
the second model is as you mentioned. Thank's for sharing again

댓글을 달려면 로그인하십시오.

chfakht chfakht
chfakht chfakht 2015년 2월 11일
Simulink with arduino : data acquisition Hello all , i'm working on data acquisition from a sensor attached to the arduino : MPU6050 using a model in simulink , i have installed the hardware support in simulink but i don't know how to start building the model , the model must read the data from arduino by deploying it into the arduino my connection arduino = MPU6050 is :
Arduino MPU 9150
3.3V VCC
any help will be appreciated thanks

zizi ove
zizi ove 2015년 6월 13일

Madhu Govindarajan
Madhu Govindarajan 2015년 10월 21일
Arduino Uno and Leonardo are not supported for external mode on Simulink -


Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by