# Plot a line between 2 points and extend the line a determined distance

조회 수: 297(최근 30일)
Alfonso 2018년 5월 27일
댓글: sloppydisk 2018년 5월 27일
I am plotting a line between points: p1 and p2. Finally I want to extend this line a determined distance so it will still pass through p1 and p2 and it will be longer.
Image 1 shows the plotted line which correctly passes through p1 and p2 But when I try to extend this line I get a longer line but with a bad angle as it does not pass through p2: Here is all the code (fillline.m is a function that can be found in File Exchange):
% Points
pto1 = [3.4353 0.2521];
pto2 = [39.5904 -20.6633];
% Original line
[line_x,line_y]=fillline(pto1(1,:), pto2(1,:),100);
line_xy = [line_x' line_y'];
plot(pto1(1), pto1(2), '+b')
hold on
plot(pto2(1), pto2(2), '.b')
hold on
plot(line_xy(:,1), line_xy(:,2), 'm') % Pintamos iterativamente las lineas
% Extend the line
factor_distance = 1.2;
theta = atan2(pto2(2) - pto1(2), pto2(1) - pto1(1)); % rad
pto2_update(1) = pto2(1) + ( factor_distance * cosd(theta) );
pto2_update(2) = pto2(2) + ( factor_distance * sind(theta) );
% Update new points in line
[line_x,line_y]=fillline(pto1(1,:), pto2_update(1,:),100);
line_xy = [line_x' line_y'];
figure
plot(pto1(1), pto1(2), '+b')
hold on
plot(pto2(1), pto2(2), '.b')
hold on
plot(line_xy(:,1), line_xy(:,2), 'm')
Thank you for any help in advance.

댓글을 달려면 로그인하십시오.

### 채택된 답변

John D'Errico 2018년 5월 27일
편집: John D'Errico 2018년 5월 27일
Why do you need filline, or anything like it? And why are you worrying about angles, etc.? You are making this far more complex than it ever needs to be.
Lets just write it from scratch. Given two points, call them as you did...
pto1 = [3.4353 0.2521];
pto2 = [39.5904 -20.6633];
% A vector along the ray from pto1 to pto2...
V = pto2 - pto1;
% The distance between the points would be:
% dist12 = norm(V);
% but there is no need to compute it.
% which will be extended (by 20% in this case) here
factor_distance = 1.2;
% Extend the ray
pext = pto1 + V*factor_distance;
% plot...
plot([pto1(1),pto2(1)],[pto1(2),pto2(2)],'bo',[pto1(1),pext(1)],[pto1(2),pext(2)],'r-') ##### 댓글 수: 2표시숨기기 이전 댓글 수: 1
sloppydisk 2018년 5월 27일
I would still advice you to just use linspace to populate the lines as it's much more elegant and easier to understand.

댓글을 달려면 로그인하십시오.

### 추가 답변(1개)

sloppydisk 2018년 5월 27일
I would first read the documentation before grabbing stuff off file exchange if I were you, because the fillline is really not necessary and there's much easier ways of plotting points. For example:
% Points
pts = zeros(2);
pts(1:2) = [1 2];
v = [2 3];
pts(3:4) = pt1 + v;
x = pts(1, :); y = pts(2, :);
plot(x, y, '-+')
% Extend the line
factor = 1.2;
pts(3:4) = pt1 + factor*v;
x = pts(1, :); y = pts(2, :);
hold on
plot(x, y, '-+')
hold off

댓글을 달려면 로그인하십시오.

### 범주

Find more on Matrices and Arrays in Help Center and File Exchange

### Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!