Find centre and diameter of the circles in the image

조회 수: 5 (최근 30일)
MechenG
MechenG 2024년 9월 29일
댓글: MechenG 2024년 9월 30일
Hi,
I am trying to find the centre (x,y) and diamter of the circles in the given image. I have played around a bit with imfindcircles. Unfortunately I didn't succed with the detection. I have attached my sample image here. Note that, in the sample image, some circles are not fully visible, this can be ignored..
Could someone help with this?

채택된 답변

Umar
Umar 2024년 9월 29일

Hi @MechenG ,

You mentioned, I am trying to find the centre (x,y) and diamter of the circles in the given image. I have played around a bit with imfindcircles. Unfortunately I didn't succed with the detection. I have attached my sample image here. Note that, in the sample image, some circles are not fully visible, this can be ignored.. Could someone help with this?

Please see my response to your comments below.

To effectively detect circles in your image and going through documentation provided at the link below,

https://www.mathworks.com/help/images/ref/imfindcircles.html

you can employ several preprocessing techniques before applying imfindcircles. The following code includes Gaussian filtering for noise reduction and morphological operations to enhance circle detection. It will also save the detected centers and diameters to a text file in the specified directory. Here is a complete MATLAB code snippet tailored to your requirements:

% Read the image
A = imread('/MATLAB Drive/Sample image.jpg'); % the image provided by you
imshow(A);
title('Original Image');
% Convert to grayscale if necessary
if size(A, 3) == 3
  A = rgb2gray(A);
end
% Apply Gaussian filtering to reduce noise
filteredImage = imgaussfilt(A, 2); % Adjust the sigma value as needed
figure; imshow(filteredImage); title('Filtered Image');
% Use edge detection to enhance circle boundaries
edges = edge(filteredImage, 'Canny');
figure; imshow(edges); title('Edge Detection');
% Apply morphological operations (dilation followed by erosion)
se = strel('disk', 2); % Create a structural element
morphedImage = imdilate(edges, se);
morphedImage = imerode(morphedImage, se);
figure; imshow(morphedImage); title('Morphological Operations');
% Define radius range for circle detection
radiusRange = [10 50]; % Adjust according to expected circle sizes
% Detect circles using imfindcircles
[centers, radii, metric] = imfindcircles(morphedImage, radiusRange, ...
                                       'ObjectPolarity', 'bright', ...
                                       'Sensitivity', 0.9, ...
                                       'EdgeThreshold', 0.1);
% Display detected circles on the original image
viscircles(centers, radii,'EdgeColor','b');
title('Detected Circles');
% Save results in text format
resultsFilePath = '/MATLAB Drive/circle_detection_results.txt';
fileID = fopen(resultsFilePath, 'w');
fprintf(fileID, 'Center (x,y), Diameter\n');
for i = 1:length(radii)
  fprintf(fileID, '(%.2f, %.2f), %.2f\n', centers(i,1), centers(i,2), 
  2*radii(i));
end
fclose(fileID);
disp(['Results saved to ', resultsFilePath]);

Please see attached.

As you can see in the code, the image is read and displayed. Since the image was in color (RGB), it is converted to grayscale since imfindcircles works on single-channel images. Afterwards, applied Gaussian Filtering because this helps reduce noise using a Gaussian filter with a specified standard deviation (sigma). You can adjust this value based on your specific image characteristics. A canny edge detection highlights the edges of potential circles. Then, utilized Morphological Operations since dilation followed by erosion helps to close gaps and enhance the shapes of detected edges. The imfindcircles function is called with a specified radius range and sensitivity settings to find circles. Circles detected are drawn on the original image for visual confirmation. The coordinates of circle centers and their diameters are saved in a specified text file format for later analysis.

Depending on your specific image conditions (e.g., lighting, contrast), you may need to adjust parameters such as the radius range or sensitivity.

After running the code, evaluate the detected circles against your expectations and refine preprocessing steps as needed for improved accuracy.

This comprehensive approach should help you successfully detect circles within your provided image while accommodating for noise and partial visibility issues.

If you have any further questions, please let me know.

추가 답변 (1개)

MechenG
MechenG 2024년 9월 30일
Hi,
Thank you very much for your detailed response. Actually, I am looking to detect only the outer edges of the big circles and it's centre (as shown in the attached image), whose radius are in the range of 170 - 190. If I give this value, it doesn't detect any circles.
  댓글 수: 3
Umar
Umar 2024년 9월 30일

Hi @MechenG,

Would it be possible to share your code on this form to help resolve this problem. Have you got chance to review the documentation provided at the link below.

https://www.mathworks.com/help/images/detect-and-measure-circular-objects-in-an-image.html

MechenG
MechenG 2024년 9월 30일
I played around a bit with a script in the suggested link. The below shown finally worked. Thanks!
[centersBright,radiiBright,metricBright] = imfindcircles(rgb,[150 300], ...
ObjectPolarity="bright",Sensitivity=0.95,EdgeThreshold=0.3);
imshow(rgb)
hBright = viscircles(centersBright,radiiBright,Color="r");

댓글을 달려면 로그인하십시오.

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by