Bringing battery simulation results (parameter estimation) to hardware

조회 수: 31(최근 30일)
Valentin
Valentin 2014년 12월 9일
댓글: Anil Shrestha 2022년 4월 18일 9:13
We are focused on battery modelling and SoC-Calculation for our electrical car, and already found provided tutorials really useful. ( Battery Models )
We've watched other battery simulation tutorials previous to this and are facing now some questions.
One big question is, how do we get the model or the simulation results later back into the car, to use the data for a live SoC-calculation in the car?
We have been thinking about creating some kind of Look-up-table out of the model, to integrate then these tables into the cars main ECU. But as we do not have any experience with this so far, we would love to know how your steps to proceed would be (assuming that the parameter estimation and everything was successful).
Attached here is one picture of our measurement files:
In your opinion, is it possible to parameterize these kind of battery cell/chemistry/behaviour with the described 1RC or a 2RC?
We really appreciate your response. Thank you very much in advance for your help!

채택된 답변

Javier Gazzarri
Javier Gazzarri 2014년 12월 19일
편집: Javier Gazzarri 2014년 12월 20일
Hello, Valentin,
Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond desktop simulation. Entire teams devote their time to developing and testing this kind of algorithms.
There is plenty of literature that you can consult to become familiar with standard techniques, requirements, and challenges.
Here is a good introduction:
-http://batteryuniversity.com/learn/article/how_to_measure_state_of_charge
- Plett, G., Extended Kalman filtering for battery management systems of LiPB-based HEV battery packs (3 parts), Journal of Power Sources 134 (2004)
- <http://mocha-java.uccs.edu/dossier/research/2008rrde-.pdf>
And here is an example that we developed based on our modeling approach
- <http://www.mathworks.com/tagteam/76108_SAE%202013%20-%20Simplified%20EKF%20Battery%20Model.pdf>
Even before thinking about generating code for your embedded controller, you must define your algorithm. It is important to take into account that the true state of charge depends on ambient and operating conditions, in addition to the amount of current that has flown in and out of the battery. The actual total capacity of a battery is in general lower at low temperatures and at high discharge rates, and these are factors that your algorithm needs to consider, for which you need a complete set of measurements.
You may want to start performing the estimation of parameters in different conditions and in this way you can assess this capacity dependence. Eventually you will have a number of look-up tables that you can think of as the “electrochemical fingerprints” of your battery. This is very important because different battery chemistry types will have very different electrical and thermal dynamic behavior. For example, the pulse discharge curve you show in your diagram will look differently at different temperatures.
Your design may include coulomb counting (keeping track of the current in and out of the battery) as a rough first estimate, since errors accumulate over time and you need some correction / recalibration. Kalman filtering is a popular way to do this, as we show in the example cited above.
Finally, you may want to consider using rapid prototyping hardware for your on-board implementation, as opposed to production hardware, to avoid all the complications associated with targeting microprocessors, such as fixed point algebra, limited memory footprint, etc.
Should you have questions during the course of your project please do not hesitate to write us and we will do whatever we can to help you.
With best wishes,
Javier Gazzarri
  댓글 수: 1
Anil Shrestha
Anil Shrestha 2022년 4월 18일 9:13
Hello Javier,
Your link to the example of Model based approach does not seems to work. Can you please, if Possible give us a workin Link to that example.
With best Regards
Shrestha

댓글을 달려면 로그인하십시오.

추가 답변(0개)

커뮤니티

더 많은 답변 보기:  Power Electronics Community

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by