Feeds
질문
How to set CAN Bus speed over 500kbps?!?
Hello guys, I am using 2ports NI CAn interface and configure them as a receiver (Port1) and a transmitter (Port2). and I can co...
6년 초과 전 | 답변 수: 0 | 0
0
답변질문
Error using Vehicle Can Bus Monitor app!!!!
Hello all, I get this eroor when I run Vehicle CAN Bus Monitor app: Error using can.ni.xnet.NIXNET.checkStatus (line 141) Nati...
6년 초과 전 | 답변 수: 0 | 0
0
답변질문
Why for loop inside MATLAB Function Block doesn't work!
Hello All, Why I can not run a simple for loop inside Matlab Function block? My code is as follow: function [out,pow...
거의 8년 전 | 답변 수: 1 | 0
1
답변질문
Solving constrained linear equation
How can I solve the following equation in Matlab? P1+P2+P3=370 I need to see all the P1,P2,P3 values that satisfy equation...
8년 초과 전 | 답변 수: 1 | 0
1
답변질문
How to use 2D look up table when input has changing dimention?
Hello All, I am trying to estimate the fuel consumption of an engine by using a look-up table. I have a fuel consumption map ...
8년 초과 전 | 답변 수: 0 | 0
0
답변질문
how to retrieve the data from simulink during simulation
I have read many posts and comments on this regard but still, coudn't figure out How can have access to block data during simula...
8년 초과 전 | 답변 수: 0 | 0
0
답변질문
Simscape phase to phase voltage measurement is not correct?
Hi, Do you have any idea why the phase-phase voltage and current has some DC component( I mean it is a bit shifted upward!)!? ...
대략 9년 전 | 답변 수: 1 | 0
1
답변질문
Why the phase-phase voltage and current measurement are like this?
Hi, Do you have any idea why my phase-phase voltage and current has DC component? It is like that my phase-phase voltage and c...
대략 9년 전 | 답변 수: 1 | 0
1
답변질문
Generic Engine and Fuel Consumption Table problem
Hi All, I have torque - power and speed characteristics of an engine and I easily used it to run the engine, but when I am addi...
대략 9년 전 | 답변 수: 0 | 0
0
답변질문
How to run Matlab function inside simulink?
I have a written code of motor which works very well in Matlab. I need to connect this code to Simulink and for this, I am using...
대략 9년 전 | 답변 수: 2 | 0
2
답변답변 있음
Simple DC/DC Converter
Try DC DC converter available in Simscape toolbox. It is easy to use and has no pulses.
Simple DC/DC Converter
Try DC DC converter available in Simscape toolbox. It is easy to use and has no pulses.
9년 초과 전 | 0
질문
How is it possible to change the frequency of average value inverter?
I need to get different output voltage frequency from Average value inverter block in Simscape. Unfortunately the block does not...
9년 초과 전 | 답변 수: 1 | 0
1
답변질문
Why the measured output active power of generator is different using two different methods?
I am using synchronous generator in Simscape. when I measure the output active power using output voltage and current and Simpow...
9년 초과 전 | 답변 수: 1 | 0
1
답변질문
How to select (or calculate) proper field current value for synchronous generator?
I have read matlab document about modeling of synchronous generator and I have the synchronous reactance value but I am not sure...
9년 초과 전 | 답변 수: 0 | 0
0
답변질문
error occur when using generic engine
I am not able to successfully use generic engine in Simscape and get error while using it (simulation suddenly stop at 0.012 sec...
9년 초과 전 | 답변 수: 0 | 0
0
답변질문
What function should I use to speed up code instead of GLOBAL
Hello, Here is my problem. I have a ODE45 solver which use part of 5 big precalculated matrixes (fixed matrxices which will n...
거의 11년 전 | 답변 수: 1 | 0
1
답변질문
global variable inside a function
Hello every one, In my program I used a solver (ODE45) and as you know, for this purpose I need to define a function. I have an...
11년 초과 전 | 답변 수: 1 | 0
