cr28
2012년부터 활동
Followers: 0 Following: 0
Feeds
제출됨
data file to the post 'grid energy storage battery'
data file of real and reactive power for 24 hrs with a 1 minute resolution
13년 초과 전 | 다운로드 수: 1 |
제출됨
grid energy storage battery
this circuit was built to simulate energy storage at the low voltage network.
13년 초과 전 | 다운로드 수: 6 |
질문
odd values of real and reactive power
In an electrical network model i built, there's a transformer that steps down voltage to 240V. I'm getting values of reactive ...
13년 초과 전 | 답변 수: 0 | 0
0
답변답변 있음
combining/concatenation mat files
thanx Azzi but this gives me a file with data written side by side i.e i get a file with 12 column...how do i merge them one bel...
combining/concatenation mat files
thanx Azzi but this gives me a file with data written side by side i.e i get a file with 12 column...how do i merge them one bel...
13년 초과 전 | 0
질문
combining/concatenation mat files
Hi, i have 4 mat files in the array format(these files are outputs from a simulink model). the variables are the same in all ...
13년 초과 전 | 답변 수: 5 | 0
5
답변질문
difference in values from similar blocks
I'm doing a discrete mode simulation of an electrical network using simpower systems. the loads in the model have a P/Q ration o...
13년 초과 전 | 답변 수: 0 | 0
0
답변질문
SIMULINK model error with 'to file'
A simulink model i created worked fine on my university system and laptop. I then added a few 'to file' blocks (to save on ram d...
13년 초과 전 | 답변 수: 2 | 0
2
답변질문
transformer output amplitude increasing oscillations
An electrical circuit I have been building is giving me strance oscillations just downstream of the transformer. The circut and ...
13년 초과 전 | 답변 수: 1 | 0
1
답변질문
using the correct source
the controlled voltage and the three-phase source block appear to be ideal voltage sources because in a simulink model that has ...
13년 초과 전 | 답변 수: 0 | 0
0
답변질문
Choosing a simulation type
Hi, I'm modelling an electrical network for a 24 hour period and looking at voltage swings and regulation.Continuous mode with ...
13년 초과 전 | 답변 수: 1 | 0
1
답변질문
phasor vs continuous simulation
running 'power_dynamicload' from the command line brings up the model of the dynamic load example. *1]* running it in phasor ...
13년 초과 전 | 답변 수: 1 | 0
1
답변질문
Simulink: Dynamic load, external PQ
A followup question to this..... http://www.mathworks.com/matlabcentral/answers/10424 Hi, I'm doing something similar to wha...
13년 초과 전 | 답변 수: 0 | 0
0
답변답변 있음
How to use a lookup table to feed parameters to a dynamic load ? Or some other way to easily adjust load PQ values? (simulink - simpower)
Hi, I'm doing something similar to what Radu did/tried to do ie external control of PQ using the demand data I have over 24 hour...
How to use a lookup table to feed parameters to a dynamic load ? Or some other way to easily adjust load PQ values? (simulink - simpower)
Hi, I'm doing something similar to what Radu did/tried to do ie external control of PQ using the demand data I have over 24 hour...
13년 초과 전 | 0
답변 있음
single phase and three phase dynamic load
Samir, All i can say is when i simulated a 3-phase dynamic load in phasor mode, the simulation was quick.....a lot quicker th...
single phase and three phase dynamic load
Samir, All i can say is when i simulated a 3-phase dynamic load in phasor mode, the simulation was quick.....a lot quicker th...
13년 초과 전 | 0
질문
control system for battery
I'm working on grid level electrical storage. The modelling process is being performed in simulink and i began using for the fir...
13년 초과 전 | 답변 수: 0 | 0
