photo

Berkin Birol


Last seen: 3개월 전 |  2018년부터 활동

Followers: 0   Following: 0

메시지

I am a Ph.D. candidate at Istanbul Technical University Control in Automation Engineering Program, and I work as a chief expert researcher for the Scientific and Technological Research Council of Turkey (TUBITAK) in Rail Transportation System Department of Information Technologies Institute (BTE) since 2009.

통계학

All
  • Thankful Level 2
  • First Review
  • 5-Star Galaxy Level 2
  • First Answer
  • Personal Best Downloads Level 1
  • First Submission
  • Thankful Level 1

배지 보기

Feeds

보기 기준

질문


grouping an equation in quadratic/squared terms
Hi all, I would like MATLAB to group my equation (-a-b)*x1^2 + 0.2*b*x1*x2 - 0.2*c*x2^2 as all quadratic items like below: ...

2년 초과 전 | 답변 수: 1 | 0

1

답변

질문


Simulation results differs when selecting accelerator mode in Simulink
Hi all, I was running simulation in accelerator mode and having some abnormalities in sim results. I run the simulation in norm...

3년 초과 전 | 답변 수: 1 | 0

1

답변

제출됨


Customizable Pulse Generator
This Simulink block allows users to change amplitude, period, width and phase delay of a square waveform signal.

4년 초과 전 | 다운로드 수: 6 |

Thumbnail

질문


How do i save the outputs of a simulink simulation runs by sim command to base workspace?
I'm running a simulation with the "sim" command like: sim('mySim', 'SimulationMode','accel','StopTime', '1000') The simulation...

4년 초과 전 | 답변 수: 1 | 0

1

답변

답변 있음
How do I pass simulink start and stop times to simulink from a .m file called by appdesigner created GUI.
One additional answer. If you plan to use tstart and tend parametric, then this works: tstart = "0.096"; tend = "0.011"; sim...

4년 초과 전 | 1

답변 있음
referenced model dynamic path option?
OK, I found the solution. I update this topic in case anyone else has same problem/need. The solution is, the "matlab project"...

대략 5년 전 | 1

| 수락됨

답변 있음
referenced model dynamic path option?
Actually, my question and problem is like this: I created a model with referenced model in C.\Users\Berkin\Desktop\myProject fo...

대략 5년 전 | 0

답변 있음
referenced model dynamic path option?
Thank you for your answer, I'll try. But I think there must be an easier way. Is it possible to create a new library and use the...

대략 5년 전 | 0

질문


referenced model dynamic path option?
Hi all, I have a question about referenced models. I use them as components, repetitive function blocks. But I have a path issu...

대략 5년 전 | 답변 수: 4 | 0

4

답변

제출됨


F_TRIG
Falling edge detector.

5년 초과 전 | 다운로드 수: 2 |

Thumbnail

제출됨


R_TRIG
Rising edge detector.

5년 초과 전 | 다운로드 수: 1 |

Thumbnail

질문


why is output of my MATLAB function in Simulink raises with slope?
Hello everyone, I tried to implement my own pulse generator with variable inputs. When I simulate it and compare results with t...

5년 초과 전 | 답변 수: 0 | 0

0

답변

질문


Simulink Matlab Function size mismatch error
Hello all, I use the following matlab function in a Simulink Matlab Function. function [igtby, igty] = fcn(input1, input2, ......

5년 초과 전 | 답변 수: 0 | 1

0

답변

질문


dealing with variable size signals
Hello all, I am dealing with variable sized outputs of Matlab fuctions in Simulink and blocks which does not support variable s...

5년 초과 전 | 답변 수: 0 | 0

0

답변

질문


exchange data between blocks using Workspace in Simulink.
Hi all, I am not experienced with MATLAB and Simulink, so I'm having some trouble to communicate two blocks with each other. ...

6년 초과 전 | 답변 수: 1 | 0

1

답변