How to generate a square wave with integer values and fixed timespan?

조회 수: 3(최근 30일)
Samuele Bolotta
Samuele Bolotta 2021년 4월 6일
편집: Adam Danz 2021년 4월 7일
I want to generate a square wave with integer values between 0 and 5 in a timespan of 30ms.
An example:
[1 1 1 1 2 2 2 4 4 4 4 4 5 5 5 5 5 5 5 5 5 0 0 0 0 0 0 0 2 2 2 2 3 3 3 ]
I've tried different things but I can't seem to find an effective way.
  댓글 수: 2
Adam Danz
Adam Danz 2021년 4월 6일
If those are the y-values, what are the corresponding x values?

댓글을 달려면 로그인하십시오.

채택된 답변

DGM
DGM 2021년 4월 7일
편집: DGM 2021년 4월 7일
Something like this. I'm assuming you want your timestep to be a uniform 30ms.
clf
% build the coarse signal
dt=0.03;
y=[1 1 1 1 2 2 2 4 4 4 4 4 5 5 5 5 5 5 5 5 5 0 0 0 0 0 0 0 2 2 2 2 3 3 3 ];
t=linspace(0,dt*numel(y),numel(y));
plot(t,y,'--b'); hold on
% but if you need better transition times, increase the resolution
tfine=linspace(0,dt*numel(y),numel(y)*100);
yfine=interp1(t,y,tfine,'nearest');
plot(tfine,yfine,'k')
While that's simple to get better transitions by interpolation, most of the signal is constant-valued. It's kind of a waste of space to have all those intermediate samples when all you really need are the points at the transitions. If you're starting from scratch, it'd be easy enough to make the vectors as needed, but let's say you're trying to work with an existing low-resolution step signal and you want to improve it without interpolating:
clf; clc
% build the coarse signal
dt=0.03;
y=[1 1 1 1 2 2 2 4 4 4 4 4 5 5 5 5 5 5 5 5 5 0 0 0 0 0 0 0 2 2 2 2 3 3 3 ];
t=linspace(0,dt*numel(y),numel(y));
plot(t,y,'--b'); hold on
% or you could reduce it to a simple series of points
% this allows a much higher effective resolution with a minimal number of samples
tt=0.0000001; % transition time
b=[t(find(diff(y)~=0)); t(find(diff(y)~=0)+1)]; % find times at steps
b=bsxfun(@plus,mean(b,1),[-tt/2;tt/2]); % reduce rise/fall time
tp=[t(1) b(:)' t(end)];
yp=interp1(t,y,tp,'nearest');
plot(tp,yp,'k')
  • Original: 35 samples, 30ms transition time
  • Full interpolation: 3500 samples, 300us transition time
  • Edges only: 14 samples, 100ns transition time
The big point is that the number of required samples in the last case is independent of transition time.
  댓글 수: 2
DGM
DGM 2021년 4월 7일
I didn't even stop to think that you could do that. I mean, it makes sense in retrospect. I'm just way too used to trying to build step signals in programs where you can't actually have vertical lines.

댓글을 달려면 로그인하십시오.

추가 답변(0개)

Community Treasure Hunt

Find the treasures in MATLAB Central and discover how the community can help you!

Start Hunting!

Translated by