FFT to convert time series data into frequency domain

I have an amplitude data of time series(2000 samples) in a file now I need to convert that into a frequency domain so that to configure at which frequencies peak amplitudes occur. here I am attaching my data file(.txt) please help me to write a code for this

Answer 1

[Star Strider]

Experiment with this:

s = readmatrix('dec.txt');

L = numel(s);                                           % Signal Length
Fs = 1E+9;                                              % Make Up Sampling Frequency & Units (Hz)
Fn = Fs/2;                                              % Nyquist Frequency
t = linspace(0, 1, L)/Fs;                               % Make Up Time Vector

figure
plot(t, s)
grid
xlabel('Time (s)')                                      % Make Up Frequency Units
ylabel('Amplitude (parsecs)')                           % Make Up Amplitude Units

FTs = fft(s - mean(s))/L;                               % Subtract Mean To See Other Peaks
Fv = linspace(0, 1, fix(L/2)+1)*Fn;                     % Frequency Vector
Iv = 1:numel(Fv);                                       % Index Vector

figure
plot(Fv, abs(FTs(Iv))*2)
grid
xlabel('Frequency (Hz)')
ylabel('Amplitude (parsecs)')

.

Answer 2

[Mathieu NOE]

hi

my little code :

clc

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% FFT parameters
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
NFFT = 4096;    % 
OVERLAP = 0.75;

% spectrogram dB scale
spectrogram_dB_scale = 80;  % dB range scale (means , the lowest displayed level is XX dB below the max level)

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% options 
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% if you are dealing with acoustics, you may wish to have A weighted
% spectrums 

% option_w = 0 : linear spectrum (no weighting dB (L) )
% option_w = 1 : A weighted spectrum (dB (A) )
option_w = 0;

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% load signal
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

%% data
% data = readmatrix('data.txt');
% alternative (older) method for txt ascii files 
fid = fopen('data.txt','r')
[data,samples] = fscanf(fid, '%12f');
fclose(fid);

Fs = 1000;  % sampling frequency (Hz)

channel = 1;
signal = data(:,channel);
samples = length(signal);

%% decimate (if needed)
% NB : decim = 1 will do nothing (output = input)
decim = 2;
if decim>1
    signal = decimate(signal,decim);
    Fs = Fs/decim;
end

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display 1 : averaged FFT spectrum
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

[freq, sensor_spectrum] = myfft_peak(signal,Fs,NFFT,OVERLAP);

% convert to dB scale (ref = 1)
sensor_spectrum_dB = 20*log10(sensor_spectrum);

% apply A weigthing if needed
if option_w == 1
    pondA_dB = pondA_function(freq);
    sensor_spectrum_dB = sensor_spectrum_dB+pondA_dB;
    my_ylabel = ('Amplitude (dB (A))');
else
    my_ylabel = ('Amplitude (dB (L))');
end


figure(1),plot(freq,sensor_spectrum_dB,'b');grid
title(['Averaged FFT Spectrum  / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(freq(2)-freq(1)) ' Hz ']);
xlabel('Frequency (Hz)');ylabel(my_ylabel);

%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
% display 2 : time / frequency analysis : spectrogram demo
%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

[sg,fsg,tsg] = specgram(signal,NFFT,Fs,hanning(NFFT),floor(NFFT*OVERLAP));  

% FFT normalisation and conversion amplitude from linear to dB (peak)
sg_dBpeak = 20*log10(abs(sg))+20*log10(2/length(fsg));     % NB : X=fft(x.*hanning(N))*4/N; % hanning only

% apply A weigthing if needed
if option_w == 1
    pondA_dB = pondA_function(fsg);
    sg_dBpeak = sg_dBpeak+(pondA_dB*ones(1,size(sg_dBpeak,2)));
    my_title = ('Spectrogram (dB (A))');
else
    my_title = ('Spectrogram (dB (L))');
end

% saturation of the dB range : 
% saturation_dB = 60;  % dB range scale (means , the lowest displayed level is XX dB below the max level)
min_disp_dB = round(max(max(sg_dBpeak))) - spectrogram_dB_scale;
sg_dBpeak(sg_dBpeak<min_disp_dB) = min_disp_dB;

% plots spectrogram
figure(2);
imagesc(tsg,fsg,sg_dBpeak);colormap('jet');
axis('xy');colorbar('vert');grid
title([my_title ' / Fs = ' num2str(Fs) ' Hz / Delta f = ' num2str(fsg(2)-fsg(1)) ' Hz ']);
xlabel('Time (s)');ylabel('Frequency (Hz)');




function pondA_dB = pondA_function(f)
	% dB (A) weighting curve
	n = ((12200^2*f.^4)./((f.^2+20.6^2).*(f.^2+12200^2).*sqrt(f.^2+107.7^2).*sqrt(f.^2+737.9^2)));
	r = ((12200^2*1000.^4)./((1000.^2+20.6^2).*(1000.^2+12200^2).*sqrt(1000.^2+107.7^2).*sqrt(1000.^2+737.9^2))) * ones(size(f));
	pondA = n./r;
	pondA_dB = 20*log10(pondA(:));
end

function  [freq_vector,fft_spectrum] = myfft_peak(signal, Fs, nfft, Overlap)
% FFT peak spectrum of signal  (example sinus amplitude 1   = 0 dB after fft).
% Linear averaging
%   signal - input signal, 
%   Fs - Sampling frequency (Hz).
%   nfft - FFT window size
%   Overlap - buffer overlap % (between 0 and 0.95)

samples = length(signal);
% fill signal with zeros if its length is lower than nfft
if samples<nfft
    s_tmp = zeros(nfft,1);
    s_tmp((1:samples)) = signal;
    signal = s_tmp;
end

% window : hanning
window = hanning(nfft);
window = window(:);

%    compute fft with overlap 
 offset = fix((1-Overlap)*nfft);
 spectnum = 1+ fix((samples-nfft)/offset); % Number of windows
%     % for info is equivalent to : 
%     noverlap = Overlap*nfft;
%     spectnum = fix((samples-noverlap)/(nfft-noverlap));	% Number of windows

    % main loop
    fft_spectrum = 0;
    for i=1:spectnum
        start = (i-1)*offset;
        sw = signal((1+start):(start+nfft)).*window;
        fft_spectrum = fft_spectrum + (abs(fft(sw))*4/nfft);     % X=fft(x.*hanning(N))*4/N; % hanning only 
    end
    fft_spectrum = fft_spectrum/spectnum; % to do linear averaging scaling

% one sidded fft spectrum  % Select first half 
    if rem(nfft,2)    % nfft odd
        select = (1:(nfft+1)/2)';
    else
        select = (1:nfft/2+1)';
    end
fft_spectrum = fft_spectrum(select);
freq_vector = (select - 1)*Fs/nfft;
end

[THONTI BEERAIAH]

Thank you for the detailed code.