Write and read I2C on arduino
조회 수: 53 (최근 30일)
이전 댓글 표시
Hey there,
I want to get the data out of the Sensirion SDP810-125Pa via my arduino. With a llibrary that I downloaded from github, the sensor works fine and gives me data via I2C and the serial moitor respectively with the Arduino IDE.
Now I wanna combine it with Matlab.
clear all
clc
myarduino = arduino('COM3','Uno','Libraries','I2C');
%scanI2CBus(myarduino,0);
pressureSensor = device(myarduino,'I2CAddress',0x25,'bitrate',100000);
write(pressureSensor, 0x361E, 'uint16');
data = read(pressureSensor, 2,'uint16');
disp(data);
I configured the I2CAddress but now it gives me the followin error.
Error using Untitled (line 6)
Error occurred while reading data from the I2C device. Check the connections between the hardware and device, clear the device object and create a
new one.
Thanks for your help!
댓글 수: 1
Danielle Park
2020년 11월 20일
Hey Benedikt,
Did you ever figure this out? I am trying to do the same but with a Sensirion SLF3S-1300F sensor.
-Danielle
답변 (3개)
Aakriti Suman
2020년 3월 27일
I understand that you want to use I2C devices on Arduino hardware.
The address that you are using for I2C communication seems incorrect. The bus address used for I2C comunication on Arduino hardware is 0x48. You can also scan the I2C bus to get the I2C address. You can try the below code snippet.
% connect all the I2C devices with the arduino and then perform the following snippet
myarduino = arduino('COM4','Uno','Libraries','I2C') % assuming that the arduino hardware is connected in COM4 serial port.
add = scanI2CBus(myarduino);
Here is an example documentation of the usage of I2C devices on arduino hardaware. This will help you in understanding the I2C communication with arduino hardware in detail. https://in.mathworks.com/help/supportpkg/arduinoio/ug/measure-temperature-from-i2c-device-on-arduino-hardware.html
I am also attaching a document which will help you with the functions that can be used in reading and writing to I2C devices connected to arduino hardware. https://in.mathworks.com/help/supportpkg/arduinoio/i2c-sensors.html?s_tid=CRUX_lftnav
댓글 수: 4
Gongyan Du
2020년 6월 12일
Hi @Aakriti Summan, My code is:
a=arduino('COM3','uno');
address = scanI2CBus(a,0);
disp(['i2c address: ', address]);
INA219 = '0x40';
Currentsensor = i2cdev(a,INA219);
INA219_ADC_CH0='40'; %CR 40
INA219_ADC_CH1='41'; % Shunt Voltage
INA219_ADC_CH2='42'; % Bus Voltage
INA219_ADC_CH3='43'; % Power
INA219_ADC_CH4='44';% Current
INA219_ADC_CH5='45';%
while 1
disp([' |CR|',' |Shunt V|',' |Bus V|',' |Power|',' |Current|',' |Cal|']);
write(Currentsensor,hex2dec(INA219_ADC_CH0));
read(Currentsensor,3,'uint16');
CR = read(Currentsensor,3,'uint16');
pause(0.1);
write(Currentsensor,hex2dec(INA219_ADC_CH1));
read(Currentsensor,3,'uint16');
V_shunt = read(Currentsensor,3,'uint16');
pause(0.1);
write(Currentsensor,hex2dec(INA219_ADC_CH2));
read(Currentsensor,3,'uint16');
V_bus = read(Currentsensor,3,'uint16');
pause(0.1);
write(Currentsensor,hex2dec(INA219_ADC_CH3));
read(Currentsensor,3,'uint16');
P = read(Currentsensor,3,'uint16');
pause(0.1);
write(Currentsensor,hex2dec(INA219_ADC_CH4));
read(Currentsensor,3,'uint16');
I = read(Currentsensor,3,'uint16');
pause(0.1);
write(Currentsensor,hex2dec(INA219_ADC_CH5));
read(Currentsensor,3,'uint16');
Cal = read(Currentsensor,3,'uint16');
pause(0.1);
disp([CR V_shunt V_bus P I Cal]);
end
serhat YILDIZHAN
2021년 6월 17일
Hi Gungyan, I will take altitude, temperature and pressure data using the I2C connection with the bmp280 sensor and draw a graph. And I'm thinking of doing this by editing your code. But I couldn't understand some parts of the code. Can you help me?
Currentsensor = i2cdev(a,INA219); %How can I define it according to bmp280?
%Can you explain how you wrote this part?
INA219_ADC_CH0='40'; %CR 40
INA219_ADC_CH1='41'; % Shunt Voltage
INA219_ADC_CH2='42'; % Bus Voltage
INA219_ADC_CH3='43'; % Power
INA219_ADC_CH4='44';% Current
Thank you.
Harsha Priya Daggubati
2020년 3월 23일
Hi,
You need to have either a Total Phase Aardvark host adapter or a NI USB-845x adapter board installed to use the i2c interface.
Refer to the following link for installation help:
You can also follow the steps listed here after the installation is successful:
These threads might be of help too:
댓글 수: 3
Harsha Priya Daggubati
2020년 3월 23일
I guess yes. Can you use write as follows similar to the one in the example.
write(pressureSensor, 0x361E, 'uint16');
참고 항목
카테고리
Help Center 및 File Exchange에서 Arduino Hardware에 대해 자세히 알아보기
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!