Main Content

In this section, you

Obtain the state-space representation of your model with the

`power_analyze`

commandCompute the steady-state voltages and currents using the graphical user interface of the Powergui block

Analyze an electrical circuit in the frequency domain

The electrical state variables are the Simulink^{®} states of your diagram associated to the capacitor and inductor
devices of the Simscape™
Electrical™ Specialized Power Systems blocks. Inductors and capacitors elements
are found in the RLC-branch type blocks such as the Series RLC Branch block,
Three-Phase Parallel RLC Load block, in the transformer models,
in the PI Section Line block, in the
snubber devices of the power electronic devices, etc.

The electrical state variables consist of the inductor currents and the capacitor
voltages. Variable names for Simscape
Electrical Specialized Power Systems electrical states contain the name of the
block where the inductor or capacitor is found, preceded by the
`Il_`

prefix for inductor currents or the
`Uc_`

prefix for capacitor voltages.

You compute the state-space representation of a model with the
`power_analyze`

command. Enter the following command at the
MATLAB^{®} prompt.

[A,B,C,D,x0,electrical_states,inputs,outputs]=power_analyze('power_gui')

The `power_analyze`

command returns the state-space model of
power_gui example model in the four
matrices A, B, C, and D. x0 is the vector of initial conditions of the electrical
states of your circuit. The names of the electrical state variables, inputs, and
outputs are returned in three matrices.

See the `power_analyze`

reference page for
more details on how to use this function.

Open the power_gui example model by typing `power_gui`

at the
command line. Then open the **Powergui Steady-State Voltages and
Currents Tool** to display the steady-state phasors voltages measured
by the voltage measurement and current measurement blocks of the model.

Each measurement output is identified by a character vector corresponding to the measurement block name. The magnitudes of the phasors correspond to the peak value of the sinusoidal voltages.

You can also display the steady-state values of the source voltage or the
steady-state values of the inductor currents and capacitor voltages by selecting
either the **Sources** or the **States** check box.

Refer to the section Measuring Voltages and Currents for more details on the sign
conventions used for the voltages and currents of sources and electrical state
variables listed in the **Steady-State Tool
**window.

The **Simscape** > **Electrical** > **Specialized Power Systems** > **Sensors and Measurements** library contains an Impedance Measurement block that
measures the impedance between any two nodes of a circuit. In the following two
sections, you measure the impedance in the power_gui model by using two methods:

Automatic measurement using the Impedance Measurement block and the Powergui block

Calculation from the state-space model

The process to measure a circuit impedance from the state-space model (which is described in detail in the next section, Obtaining the Impedance vs. Frequency Relation from the State-Space Model) has been automated in a Simscape Electrical Specialized Power Systems block. In the power_gui example model, two Impedance Measurement blocks of powerlib measure impedance at two points in the model. Delete the Impedance B3 block and reconnect the Impedance B1 as shown.

**Measuring Impedance vs. Frequency with the
Impedance Measurement Block**

In the** 150 km Line** block, set **Number of pi
sections** to 1, and click **OK**. Open the
Powergui dialog. In the **Tools** tab, select
**Impedance Measurement**. A new window opens,
showing the list of Impedance Measurement blocks
available in the circuit.

Fill in the frequency range by entering `0:2:5000`

(zero to
5000 Hz by steps of 2 Hz). Select the logarithmic scale to display Z
magnitude.

When the calculation is finished, the window displays the magnitude and phase
as functions of frequency. In the **150 km Line** block dialog
box, set the **Number of pi sections** to 10. In the Powergui
Impedance vs Frequency Measurement tool, click the **Update**
button. The block dialog box displays the frequency response for the new
circuit.

**Note**

The following section assumes that you have Control System Toolbox™ software installed.

To measure the impedance versus frequency at the same node where the impedance measurement block is
connected, you need a current source providing a second input to the state-space
model. Add the AC Current Source block from
the **Simscape** > **Electrical** > **Specialized Power Systems** > **Sources** library to your model. Connect this source, as shown below. Set
the current source magnitude to zero and keep its frequency at ```
60
Hz
```

.

**AC Current Source at the B2 Node**

Now compute the state-space representation of the model with the
`power_analyze`

command. Enter the following command at
the MATLAB prompt.

sys1 = power_analyze('power_gui','ss')

This command returns a state-space model representing the continuous-time state-space model of your electrical circuit.

In the Laplace domain, the impedance is defined as the transfer function between the current injected by the AC current Source block and the voltage measured by the U2 Voltage Measurement block.

$$Z2\left(s\right)=\frac{U2\left(s\right)}{I2\left(s\right)}$$

You obtain the names of the inputs and outputs of this state-space model as follows.

sys1.InputName ans = 'U_Vs (60Hz)' 'I_AC Current Source' sys1.OutputName ans = 'U_Ub2' 'U_Ub1'

The impedance at the measured node then corresponds to the transfer function between output 1 and input 2 of this state-space model. For the 0–5000 Hz range, it can be calculated and displayed as follows.

freq=0:5000; w=2*pi*freq; bode(sys1(1,2),w);

Repeat the same process to get the frequency response with a 10 section line
model. Open the **PI Section Line** dialog box and
change the number of sections from `1`

to
`10`

. To calculate the new frequency response and superimpose
it upon the one obtained with a single line section, enter the following
commands.

sys10 = power_analyze('power_gui','ss'); bode(sys1(1,2),sys10(1,2),w);

Open the property editor of the Bode plot and select units for Frequency in Hz using linear scale and Magnitude in absolute using log scale. The resulting plot is shown below.

**Impedance at the Measured Node as Function of
Frequency**

This graph indicates that the frequency range represented by the single line section model is limited and the 10 line section model gives a better approximation for higher frequencies.