Running Simulink models on a TI C2000 MCU
조회 수: 2(최근 30일)
I have a problem concerning Simulink Coder. I wanted to compile a simple Simulink model to run it on the C2000 Microcontroller F28069M by Texas Instruments (TI) (the model should only toggle a GPIO pin every half a second). In the Model Configuration I already chose all the right options: I selected the right target hardware, chose the mode "Build, load and run" and I also checked the option "Boot from flash". But Simulink only seemed to build the C code without running it on the MCU. There was not even an error when I clicked on "Build" and had the MCU disconnected. Then I deactivated the checkbox "Generate code only" in the Simulink preferences and now Simulink seems to do what I want. But everytime I am trying to build the model, an error occurs in the Diagnostic Viewer:
C:/TI_CCSv6/ccsv6/tools/compiler/TI-CGT~1.1/bin/cl2000 --compile_only --large_memory_model --cla_support=cla0 --silicon_version=28 --define="LARGE_MODEL" -i"/~SupportFiles/DSP280x_headers" -i"/~SupportFiles/DSP280x_headers/include" -i"C:/TI_CCSv6/ccsv6/tools/compiler/TI-CGT~1.1/include" -v28 -ml --float_support=fpu32 -DMODEL=Toggle_Pin_J1_Nr5 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -DONESTEPFCN=1 -DTERMFCN=0 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=1 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -D__MW_TARGET_USE_HARDWARE_RESOURCES_H__ -DRT -DSTACK_SIZE=512 -DONESTEPFCN=1 -DTERMFCN=0 -DMAT_FILE=0 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=1 -DMT=0 -DCLASSIC_INTERFACE=0 -DALLOCATIONFCN=0 -DTID01EQ=0 -DRT -DSTACK_SIZE=512 -DMODEL=Toggle_Pin_J1_Nr5 -DNUMST=1 -DNCSTATES=0 -DHAVESTDIO -IC:/Users/Armin/Documents/MATLAB/Toggle_Pin_J1_Nr5_ert_rtw -IC:/Users/Armin/Documents/MATLAB -IC:/PROGRA~1/MATLAB/extern/include -IC:/PROGRA~1/MATLAB/simulink/include -IC:/PROGRA~1/MATLAB/rtw/c/src -IC:/PROGRA~1/MATLAB/rtw/c/src/ext_mode/common -IC:/PROGRA~1/MATLAB/rtw/c/ert -IC:/MATLAB_Packages/texasinstrumentsc2000/toolbox/target/supportpackages/tic2000/src -IC:/PROGRA~1/MATLAB/toolbox/target/extensions/processor/tic2000/include -IC:/PROGRA~1/MATLAB/toolbox/rtw/targets/common/can/blocks/tlc_c -IC:/MATLAB_Packages/texasinstrumentsc2000/toolbox/target/supportpackages/tic2000/inc -IC:/TI_ControlSUITE/device_support/f2806x/v151/F2806x_common/include -IC:/TI_ControlSUITE/device_support/f2806x/v151/F2806x_headers/include -IC:/PROGRA~1/MATLAB/toolbox/shared/can/src/scanutil --output_file="MW_c28xx_board.obj" "MW_c28xx_board.c"
The command "C:/TI_CCSv6/ccsv6/tools/compiler/TI-CGT~1.1/bin/cl2000" is either written wrong or could not be found.
The configuration of the Embedded Coder Package for C2000 MCUs was successful and I set every path to the TI software components correctly. Why does Simulink suddenly need the path "C:/TI_CCSv6/ccsv6/tools/compiler/TI-CGT~1.1/bin/cl2000" which I never specified during the setup? The communication between my laptop and the MCU should also be okay, because I can establish a connection via Code Composer Studio (CCSv6) by TI. I am using MATLAB R2015b. Could someone help me resolving this problem?
Best regards, Armin