이 페이지는 기계 번역을 사용하여 번역되었습니다. 최신 내용을 영문으로 보려면 여기를 클릭하십시오.
시스템 코어
STM32 프로세서에서 사용 가능한 GPIO, 하드웨어 인터럽트, DMA 등의 시스템 코어 주변기기로 Simulink® 모델을 만듭니다. 모델 구성 파라미터를 사용하여 지원되는 타깃 하드웨어와 인터페이싱하도록 Simulink 모델을 구성합니다.
Simulink에서의 STM32 프로세서 기반 보드에 대한 지원은 STM32CubeMX 그래픽 툴을 사용합니다. STM32CubeMX 툴은 STM32 프로세서의 주변기기를 구성하고 선택한 STM32 프로세서에 대한 주변기기 초기화 코드를 생성하는 데 사용할 수 있는 그래픽 인터페이스입니다. Simulink에서 STM32CubeMX 프로젝트를 사용하여 STM32 프로세서 기반 보드를 구성해 코드를 생성하고 해당 코드를 하드웨어에 배포할 수 있습니다.
블록
| Digital Port Write | Set GPIO pin status (R2021b 이후) |
| Digital Port Read | Read GPIO pin status (R2021b 이후) |
| Hardware Interrupt | Trigger downstream function-call subsystems from interrupt service routine (R2021b 이후) |
도움말 항목
- Configure STM32 Processor-Based Boards using STM32CubeMX with Simulink
Configure the STM32 Processors-Based Boards to use STM32CubeMX project with Simulink.
- Set Up Scheduling Options for STM32 Processor-Based Boards
Setting up scheduling options for STM32 processor based boards.
- STM32CubeMX Configuration for Voltage Mode Control
Instructions for STM32CubeMX configuration.
- Use SoC Blockset Pass-Through Block Simulation
Use the SoC Blockset™ block pass through to add simulation to STM blocks.
추천 예제
Getting Started with STMicroelectronics STM32 Processor Based Boards
Use the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors to run a Simulink® model on an STMicroelectronics STM32 Processor Based hardware board.
Using Hardware Interrupt Block to Create an ISR on STMicroelectronics STM32 Processor Based Boards
Use a Hardware Interrupt block to create an interrupt service routine (ISR) in the generated code for Embedded Coder® Support Package for STMicroelectronics® STM32 Processors Based Boards.
Optimizing FreeRTOS Scheduling on STM32 Processors
Demonstrates how to use the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors to execute a Simulink® model on the STMicroelectronics NUCLEO-F207ZG board. It guides you through implementing FreeRTOS scheduling within the STM32CubeMX workflow, enabling efficient task management and code execution.
MAT-file Logging on SD Card for STMicroelectronics STM32 Processors
Perform MAT-file logging using Simulink model on a Micro SD card mounted on an STMicroelectronics STM32 Discovery board.
Getting Started with Hardware Profiling
Demonstrates how to perform real-time execution profiling of algorithms using the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors. It covers two primary profiling methods:
Push Button and LED
Use the GPIO blocks in the to control the push-button and the LED components by using the Embedded Coder® Support Package for STMicroelectronics® STM32 Processors
