답변 있음
How to model an inductor whose inductance value changes with RMS current passing through it?
Hi Jay, This is a modeling problem. Ideally, if the data points are sufficiently available, you can use the Curve Fitting to...

1년 초과 전 | 0

답변 있음
Solver was unable to reduce the step size without violating the minimum step size value of 2.66454E-10 for 5 consecutive times
Hi @Juan José Good to hear that the custom smooth signal works. The masked subsystem is able to generate the trapezoidal pulse ...

1년 초과 전 | 0

| 수락됨

답변 있음
how to simulate mpc controller?
Hi @Mikail, I did not 'beautify' the plot. But the following outlines how you can simulate the LQR-controlled system using the ...

1년 초과 전 | 0

| 수락됨

답변 있음
Standard form of Transfer function.
Hi @Hamza Harbi This display of the transfer function is not referred to as the 'Standard form', or rather, it is known as the ...

1년 초과 전 | 0

| 수락됨

답변 있음
Need help with troubleshooting and how can I fix these errors in my code?
Hi @Tiek Aun I am unfamiliar with the dynamics of the pyrolysis reactor; however, I can point out two mistakes in the code. Fi...

1년 초과 전 | 0

| 수락됨

답변 있음
Algebraic Loop Error in Simulink Model with Enabled Subsystems – Performance Issue
Hi @Marco Your case sounds similar to the flip-flop. It creates a circular dependency between the output and input values of th...

1년 초과 전 | 0

답변 있음
Sliding Mode Control (SMC) + PID Cascade Loop
Hi @Junaid I understand that the clamping force must be increased incrementally from 0 kN and must not exceed 6 kN. You aim to ...

1년 초과 전 | 0

답변 있음
Implementing MRAC for Robotic arm of unknown link lengths
Hi @Sandy Based on your image, the MRAC block should replace the Sum and PID controller blocks. If the link length is unknown, ...

1년 초과 전 | 0

| 수락됨

답변 있음
My Step Response plot from Matlab does not match the one from Simulink
Hi @Javier If you want the Simulink Step block to match the MATLAB step() command, please follow @Paul's guidance. Conversely, ...

1년 초과 전 | 0

| 수락됨

답변 있음
How to plan path in Cartesian coordinate for robotic manipulator
Hi @Kannan For a more complex path, such as the M-shaped Golden Arches, you will need to describe the path using parameterized ...

1년 초과 전 | 0

| 수락됨

답변 있음
Hi everyone, help me understand the meaning of the 2 parameters Kv Ki in the measurement block in the Bus block, and how to determine that parameter.
Hai @hai, The electronic amplifier-like block is referred to as the 'Gain' block, which multiplies the input by a constant valu...

1년 초과 전 | 0

| 수락됨

답변 있음
Ezyfit: Single vs. Two-Step Fitting Problem
Hi @Sim You can verify this. The model proposed by @Torsten fits quite well within the first 10% of the data range. However, af...

1년 초과 전 | 1

답변 있음
Stability Margins for MIMO Feedback Loop
Hi @Florian If you wish to determine the stability margin of a linearized system, you may consider using the Bode Plot block di...

1년 초과 전 | 0

답변 있음
I have been trying to derivate equation under to find the formula for 3 parameters Weibull distribution as same as picture. Can someone please help me fix it?
Is this what you are seeking? Your equation is too lengthy and contains excessive, unnecessary brackets, as well as mismatched ...

1년 초과 전 | 0

| 수락됨

답변 있음
Open-Loop Response of a Simulink MIMO System
I am unsure whether your modeling is correct; however, one obvious observation from the Scope is that you are comparing the outp...

1년 초과 전 | 0

답변 있음
Solution of algebraic equation that a variable occures both in numerator and denomirator with respect to an other variable
Γεια @Anastasios Kyriakopoulos I would like to show graphically that the nonlinear equation is not strictly a quadratic equatio...

1년 초과 전 | 0

답변 있음
How to determine if equation is not feedback linearizable
Hi @Ken I am not aware of a specific function in MATLAB to test whether a system is feedback linearizable. However, the given s...

1년 초과 전 | 1

| 수락됨

답변 있음
Machine and Deep Learning Books using MATLAB
Hi @Ahmed You can find the info about the books that provide codes for machine learning and deep learning using MATLAB here: h...

1년 초과 전 | 1

| 수락됨

답변 있음
how to write mat lab code for predict compressive strength of concrete using svm
Hi @Rathnaswamy You can use the data on concrete specimens with varying mix proportions and curing ages to train an SVM model u...

1년 초과 전 | 0

답변 있음
How can I use the function coeffs() as the input to the function tf()?
Use double(). syms s n = (s^2+10*s+50)*(s^2+8.6*s+21.73)*(s^2-0.7*s+0.1625)*(s^2-2*s+3.25)^2*(s^2+4)^2*(s-2.2); x = expand(n)...

1년 초과 전 | 1

| 수락됨

답변 있음
How can I calculate the probability of false detection?
@Suleyman Aliyev, Do you expect the graph to behave like this? % Given parameters sigma2_values = linspace(0.1, 0.01, 100); ...

1년 초과 전 | 2

답변 있음
Need help with DC motor modelling with PID
Hi @Irwan Shah The looping in your model is incorrect due to unit inconsistency. All calculations are performed in radians. Y...

1년 초과 전 | 0

| 수락됨

답변 있음
Problem with derivative block simulink
Hi @Purvaja Based on the information provided by the OP, I will likely construct the model as illustrated. However, if the refe...

1년 초과 전 | 1

답변 있음
How to use the integrating option in a closed-loop PID autotuner?
Here is the difference between stable plants and integrating plants: %% Stable Plant (all eigenvalues have negative real part) ...

1년 초과 전 | 0

답변 있음
I need help for drawing a constraint in Matlab in 2D
Hi @nadia nadi You should replace the p3 line with this: p3 = 3/2*ones(1, numel(x1(1,:))); ... plot(p3, x1(1,:)) clear...

1년 초과 전 | 0

| 수락됨

답변 있음
Request for MATLAB Code of Elephant Search Algorithm (ESA)
Hi @Sina The most effective approach is to contact the authors, as the algorithm was originally coded in MATLAB. They would ben...

1년 초과 전 | 1

답변 있음
solve algebric loop error
Hi Shabina, The error suggests that you have incorrectly modeled the dynamic system, resulting in a singularity. This is ...

1년 초과 전 | 0

답변 있음
"Hold Value" of a Fuzzy Control while no rule is active
Hi @Daniel If none of the rules is triggered for any output, the defuzzified output value will default to its mean range value,...

1년 초과 전 | 0

답변 있음
Error using type too many output arguments
Possibly syntax error. The strcmpi() function is used to compare strings. So, you need to place the texts in double quotes. %va...

1년 초과 전 | 0

답변 있음
iztrans giving unexpected outputs
Another way is to provide a proof by contradiction. Misprints can happen due to a lack of proofreading. syms n f1 = n*(-1)^...

1년 초과 전 | 0

| 수락됨

더 보기