mfilt.iirdecim

IIR decimator

Compatibility

Note

mfilt.iirdecim will be removed in a future release. Use dsp.IIRHalfbandDecimator instead.

Syntax

hm = mfilt.iirdecim(c1,c2,...)

Description

hm = mfilt.iirdecim(c1,c2,...) constructs an IIR decimator filter given the coefficients specified in the cell arrays c1, c2, and so on. The resulting IIR decimator is a polyphase IIR filter where each phase is a cascade allpass IIR filter.

Each cell array ci contains a set of vectors representing a cascade of allpass sections. Each element in one cell array is one section. For more information about the contents of each cell array, refer to dfilt.cascadeallpass. The contents of the cell arrays are the same for both filter constructors and mfilt.iirdecim interprets them same way as mfilt.cascadeallpass.

The following exception applies to interpreting the contents of a cell array — if one of the cell arrays ci contains only one vector, and that vector comprises a series of 0s and one element equal to 1, that cell array represents a dfilt.delay section with latency equal to the number of zeros, rather than a dfilt.cascadeallpass section. This exception case occurs with quasi-linear phase IIR decimators.

Although the first example shows how to construct an IIR decimators explicitly, one usually constructs an IIR decimators filter as a result of designing an decimators, as shown in the subsequent examples.

Examples

When the coefficients are known, you can construct the IIR decimator directly using mfilt.iirdecim. For example, if the filter's coefficients are [0.6 0.5] for the first phase in the first stage, 0.7 for the second phase in the first stage and 0.8 for the third phase in the first stage; as well as 0.5 for the first phase in the second stage and 0.4 for the second phase in the second stage, construct the filter as shown here.

Hm = mfilt.iirdecim({[0.6 0.5] 0.7 0.8},{0.5 0.4})

Also refer to the “Quasi-Linear Phase Halfband and Dyadic Halfband Designs” section of the “IIR Polyphase Filter Design” example, IIR Halfband Stages in Multistage Filter Design example.

When the coefficients are not known, use the approach given by the following set of examples. Start by designing an elliptic halfband decimator with a decimation factor of 2. The example specifies the optional sampling frequency argument.

tw = 100;   % Transition width of filter.
ast = 80;   % Stopband attenuation of filter.
fs = 2000;  % Sampling frequency of signal to filter.
m = 2;      % Decimation factor.
hm = fdesign.decimator(m,'halfband','tw,ast',tw,ast,fs);

hm contains the specifications for a decimator defined by tw, ast, m, and fs.

Use the specification object hm to design a mfilt.iirdecim filter object.

d = design(hm,'ellip','filterstructure','iirdecim'); 
% Note that realizemdl requires Simulink
realizemdl(d)     % Build model of the filter.

Designing a linear phase decimator is similar to the previous example. In this case, design a halfband linear phase decimator with decimation factor of 2.

tw  = 100;  % Transition width of filter.
ast = 60;   % Stopband attenuation of filter.
fs  = 2000; % Sampling frequency of signal to filter.
m = 2;      % Decimation factor.

Create a specification object for the decimator.

hm = fdesign.decimator(m,'halfband','tw,ast',tw,ast,fs);

Finally, design the filter d. 

d = design(hm,'iirlinphase','filterstructure','iirdecim'); 
% Note that realizemdl requires Simulink
realizemdl(d)  % Build model of the filter.

The filter implementation appears in this model, generated by realizemdl and Simulink®.

Given the design specifications shown here

the first phase is a delay section with 0s and a 1 for coefficients and the second phase is a linear phase decimator, shown in the next models.

Phase 1 model

Phase 2 model

Overall model

Version History

Introduced in R2011a

See Also

| |