답변 있음

Using fuel cell stack and battery with electrical domain

Hello Hugo, Thank you for your question. Please see if any of the Interface Elements in Simscape/Electrical/Specialized Power ...

Using fuel cell stack and battery with electrical domain

Hello Hugo, Thank you for your question. Please see if any of the Interface Elements in Simscape/Electrical/Specialized Power ...

대략 3년 전 | 1

| 수락됨

답변 있음

Cell Balancing Model in Simulink

Hello Sanya, Here is an example you may use to start your design. The bleed resistor has to be adjusted to the unit cell size ...

Cell Balancing Model in Simulink

Hello Sanya, Here is an example you may use to start your design. The bleed resistor has to be adjusted to the unit cell size ...

대략 3년 전 | 0

| 수락됨

답변 있음

Initial Equations in Simscape Custom Models

Thank you Christopher. I see your point. The issue with initialization may be the result of this way of defining VOC. There is...

Initial Equations in Simscape Custom Models

Thank you Christopher. I see your point. The issue with initialization may be the result of this way of defining VOC. There is...

3년 초과 전 | 0

답변 있음

Read a parameter/block value only at the initialization in Simulink

Hello Lucifer, Thank you for your question. Please see the attachment I created. If you put that block in series with the volt...

Read a parameter/block value only at the initialization in Simulink

Hello Lucifer, Thank you for your question. Please see the attachment I created. If you put that block in series with the volt...

3년 초과 전 | 0

답변 있음

What is the definition and function of temperature break point in Equivalent Circuit Battery Block(Simulink)?

Hello Leon, Thank you for your question. The breakpoints indicate the temperature values for which you need to have OCV and in...

What is the definition and function of temperature break point in Equivalent Circuit Battery Block(Simulink)?

Hello Leon, Thank you for your question. The breakpoints indicate the temperature values for which you need to have OCV and in...

3년 초과 전 | 0

| 수락됨

답변 있음

Initial Equations in Simscape Custom Models

Hello Christpher, Thank you for your inquiry. I am not sure if I understand your approach, so I have a couple of clarification...

Initial Equations in Simscape Custom Models

Hello Christpher, Thank you for your inquiry. I am not sure if I understand your approach, so I have a couple of clarification...

3년 초과 전 | 0

답변 있음

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your clarification. If you need to switch heat transfer on and off in a thermal circuit you can u...

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your clarification. If you need to switch heat transfer on and off in a thermal circuit you can u...

3년 초과 전 | 0

답변 있음

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your good wishes. What you are trying to do is possible, but using Simscape makes it much easier ...

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your good wishes. What you are trying to do is possible, but using Simscape makes it much easier ...

3년 초과 전 | 0

답변 있음

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your question. Simscape Electrical has a battery cell block which has the option of turning on the...

How could I control the thermal coupling between two elements (e.g. two battery cell)?

Dear Mustafa, Thank you for your question. Simscape Electrical has a battery cell block which has the option of turning on the...

3년 초과 전 | 0

답변 있음

How can I speed up my simualtion?

Hello Raphael, Thank you for sharing this. There are several ways in which you could speed up your simulation. They include: R...

How can I speed up my simualtion?

Hello Raphael, Thank you for sharing this. There are several ways in which you could speed up your simulation. They include: R...

3년 초과 전 | 0

답변 있음

Change the capacity of the battery using Generate Parameter Data for Equivalent Circuit Battery Block

Dear Sumukh, The capacity in that block is Battery capacity table. On line 200 of the script Example_DischargePulseEstimation.m...

Change the capacity of the battery using Generate Parameter Data for Equivalent Circuit Battery Block

Dear Sumukh, The capacity in that block is Battery capacity table. On line 200 of the script Example_DischargePulseEstimation.m...

3년 초과 전 | 0

답변 있음

How do I simulate battery performance in the next 5 years, using existing 5 years trend?

Dear L. Sugu, Thank you for your inquiry. If you have capacity fade and internal resistance increase as part of your last 5 ye...

How do I simulate battery performance in the next 5 years, using existing 5 years trend?

Dear L. Sugu, Thank you for your inquiry. If you have capacity fade and internal resistance increase as part of your last 5 ye...

3년 초과 전 | 0

답변 있음

Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid

Hi, Md., You can still use SPS in that case. The main difference with SimElectronics is that the latter models all nonlineari...

Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid

Hi, Md., You can still use SPS in that case. The main difference with SimElectronics is that the latter models all nonlineari...

대략 8년 전 | 0

답변 있음

¿Why the battery (electrical source component in SimPowerSystem Matlab/Simulink toolbox) discharge at the same rate with different capacities?

Hello, Jorge, I am attaching a model like you describe above and it seems to work correctly for me. Please make sure you cli...

¿Why the battery (electrical source component in SimPowerSystem Matlab/Simulink toolbox) discharge at the same rate with different capacities?

Hello, Jorge, I am attaching a model like you describe above and it seems to work correctly for me. Please make sure you cli...

대략 8년 전 | 0

| 수락됨

답변 있음

Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid

Hello, Md., If the AC part of your system is three-phase and you can neglect thermal effects on the semiconductor devices and...

Simulink toolbox to model pv array, battery, inverter, dc-dc converter, mppt, grid

Hello, Md., If the AC part of your system is three-phase and you can neglect thermal effects on the semiconductor devices and...

대략 8년 전 | 0

답변 있음

How can I generate the setup of AC sweep for AC Voltage source in either Matlab or simulink?

Hello, Robert, I believe the Chirp Signal may do the job for you. It is in the Sources section of the Simulink library. Be...

How can I generate the setup of AC sweep for AC Voltage source in either Matlab or simulink?

Hello, Robert, I believe the Chirp Signal may do the job for you. It is in the Sources section of the Simulink library. Be...

8년 초과 전 | 0

| 수락됨

답변 있음

Problems with model behaviour, hanging-up in a loop.

Hello, Joel, Would you please attach the model to this thread so I can take a look and try to better understand the issue? ...

Problems with model behaviour, hanging-up in a loop.

Hello, Joel, Would you please attach the model to this thread so I can take a look and try to better understand the issue? ...

8년 초과 전 | 0

| 수락됨

답변 있음

How to model a solar powered electric grid in Simulink?

Hello, Faraz, I suggest you consider the use of SimPowerSystems for your design. You can find some examples here: http://w...

How to model a solar powered electric grid in Simulink?

Hello, Faraz, I suggest you consider the use of SimPowerSystems for your design. You can find some examples here: http://w...

8년 초과 전 | 1

| 수락됨

답변 있음

Simscape thermal mass discrete model

Dear Lalumet, A discrete solver can be used if you set up "Use Local Solver" in the Simscape Solver configuration block. Ple...

Simscape thermal mass discrete model

Dear Lalumet, A discrete solver can be used if you set up "Use Local Solver" in the Simscape Solver configuration block. Ple...

8년 초과 전 | 0

답변 있음

How to make a Variable resistor in Sim powersystem not Simscape.

Hello, Adroit, You can combine a current meter and a controlled voltage source to create a variable resistor. Please see att...

How to make a Variable resistor in Sim powersystem not Simscape.

Hello, Adroit, You can combine a current meter and a controlled voltage source to create a variable resistor. Please see att...

8년 초과 전 | 2

| 수락됨

답변 있음

Battery Model Simulink for 12V

Hi, Samad, Please open the battery cell block and comment out the SOC, DOC, and T blocks. This will prevent the second error ...

Battery Model Simulink for 12V

Hi, Samad, Please open the battery cell block and comment out the SOC, DOC, and T blocks. This will prevent the second error ...

8년 초과 전 | 1

| 수락됨

답변 있음

How to connect generic battery to an electrical circuit which is created using Simscape??

Hello, Mirza, Yes, that is possible. There are a couple of options: 1) Use SimPowerSystems Simscape Components. The blocks...

How to connect generic battery to an electrical circuit which is created using Simscape??

Hello, Mirza, Yes, that is possible. There are a couple of options: 1) Use SimPowerSystems Simscape Components. The blocks...

8년 초과 전 | 0

| 수락됨

답변 있음

lead acid battery simulink

Hello, Simon, You may want to check this submission for an example of what you are trying to model: http://www.mathworks.c...

lead acid battery simulink

Hello, Simon, You may want to check this submission for an example of what you are trying to model: http://www.mathworks.c...

거의 9년 전 | 0

답변 있음

Battery Model Simulink for 12V

Hi, Samad, The series connection in Simscape is realized connecting the + terminal of each cell to the - terminal if the adja...

Battery Model Simulink for 12V

Hi, Samad, The series connection in Simscape is realized connecting the + terminal of each cell to the - terminal if the adja...

거의 9년 전 | 0

답변 있음

Bringing battery simulation results (parameter estimation) to hardware

Hello, Valentin, Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond des...

Bringing battery simulation results (parameter estimation) to hardware

Hello, Valentin, Designing an accurate SOC estimator for embedded implementation is a very involved task that goes beyond des...

거의 9년 전 | 0

| 수락됨

답변 있음

How to connect generic battery to an electrical circuit which is created using Simscape??

Hello, Mirza, Can you please attach a screenshot of your model so that I can take a look? Your problem is typically related ...

How to connect generic battery to an electrical circuit which is created using Simscape??

Hello, Mirza, Can you please attach a screenshot of your model so that I can take a look? Your problem is typically related ...

거의 9년 전 | 0

답변 있음

Error with Simscape simulating

Hello, Nikolaos, Your model is missing an electrical reference (ground). Please add one and let me know if you still get an e...

Error with Simscape simulating

Hello, Nikolaos, Your model is missing an electrical reference (ground). Please add one and let me know if you still get an e...

거의 9년 전 | 3

답변 있음

Recharge battery by induction on simulink

Hello, Titouan, Please try inserting an electrical reference block on the right hand side of your magnetic circuit. It needs ...

Recharge battery by induction on simulink

Hello, Titouan, Please try inserting an electrical reference block on the right hand side of your magnetic circuit. It needs ...

거의 9년 전 | 0

| 수락됨