Community Profile

# Kostas

##### Last seen: Today
23 2019 이후 총 참여 횟수

#### Kostas's 배지

세부 정보 보기...

참여 게시물
보기 기준

질문

How to reshape an array in a specific manner
Hi all, I was trying to reshape an array in a specific manner, however I couldn't accomplish that. Here is the example: I hav...

7일 전 | 답변 수: 2 | 0

### 2

답변

질문

Access previous iteration in while loop to derive stopping criterion for differential equation correction-prediction method
Hi all, I have been trying to write a prediction-correction method for matrix differential equations, however I have been unsu...

약 1달 전 | 답변 수: 1 | 0

### 1

답변

질문

ODE45 stop when steady state occurs in a periodic function
Hi all, I have a typical set of equations for a forced spring-mass-damper system, which I have managed to solve successfully. ...

2달 전 | 답변 수: 1 | 0

### 1

답변

질문

Too many input arguments for Max function in 2018b
Hi all, I am using the function 'max' in its newest format for 2018b, as shown here, and I have the following code: A = randi...

2달 전 | 답변 수: 1 | 0

### 1

답변

질문

Find zeros of numeric function
Hi all, I have a numeric function which for the sake of simplicity resembles the following: x = linspace(1:100) ; y = sin(x...

3달 전 | 답변 수: 1 | 0

### 1

답변

질문

ODE45 calculating the total energy in the system and checking the solver
Hi all, I have a simple code written for a 3 degree of freedom damped cart-mass system. My aim is that besides by solving for ...

3달 전 | 답변 수: 1 | 0

### 1

답변

질문

Convergence with fsolve?
Hi all, I was trying to solve a system of equations using fsolve that I havent' been succesfull in doing so. So I have the fol...

4달 전 | 답변 수: 0 | 0

### 0

답변

질문

Simscape custom component to have one parameters unit change depending on the input of another parameter
Hi all, I am creating a custom simscape block and it all works fine, except the units. The equation is Torq = D1*w + D2*w^PE a...

4달 전 | 답변 수: 0 | 0

### 0

답변

답변 있음
How to dynamically size arrays in Simscape custom component?
Have you tried writing right next to your inputs something like: inputs (Size = Variable). I do not know if it works but it is s...

4달 전 | 0

질문

Hi all, I have created a 2 degree of freedom model of an engine driving a propeller with a 'flexible crankshaft' modelled in s...

4달 전 | 답변 수: 0 | 0

### 0

답변

답변 있음
How to make a new Simscape model in ".ssc" File.
Well.. I was running into the exact same problem as @Yji Ito and @Chris Matthews run into. After experimenting I managed to get ...

4달 전 | 0

질문

Simulink 'To File' Block: How to save simulation outputs as distinct vectors
Hi all, How is it possible to save in simulink a bunch of simulation outpus in the same .mat file (using the 'To File' block),...

4달 전 | 답변 수: 1 | 0

### 1

답변

답변 있음
Hi there, Would the code below help? Essentially you can use sprintf function to create a cell array with all the file names...

4달 전 | 0

| 수락됨

질문

Simulink error: The data abscissae must be distinct and strictly monotonic.
Hi all, I have constructed a simulink model, where within the model I have a MATLAB function block as you can see. Within that ...

4달 전 | 답변 수: 1 | 0

### 1

답변

답변 있음
Solver for nonlinear second order ODE has large residuals when mass matrix becomes state dependent
I ended up solving the above equation with sufficiently low residuals, by choosing a sufficiently small tspan and running the od...

4달 전 | 1

| 수락됨

질문

Solver for nonlinear second order ODE has large residuals when mass matrix becomes state dependent
Hi all, I currently have a nonlinear second order ODE that when I try to solve with any of MATLAB's ODE solvers, I get unaccep...

4달 전 | 답변 수: 2 | 0

### 2

답변

질문

ode45 unexpected behaviour for initial conditions = 0
Hi all, I have a code where I am using it to solve the following differential equation: In specific, the above is a 4x4 sys...

5달 전 | 답변 수: 1 | 0

### 1

답변

질문

How to determine convergence of ode45
Hi all, I was wondering how it is possible to determine convergence of ode45 for a simple damped mass-spring system. So here i...

5달 전 | 답변 수: 0 | 0

### 0

답변

질문

How to extract the value of dydt from ode45 function
Hi all, I have written a code of a damped mass-spring system, that takes as inputs the relevant mass, damping, stiffness and ex...

5달 전 | 답변 수: 1 | 0

### 1

답변

질문

Change from set notation to dot notation
Hi all, Just in order to keep uniformity in my code, I would like to know if its possible to change the below expression fro...

7달 전 | 답변 수: 1 | 0

### 1

답변

답변 있음
ODE45 Multiple Degrees of Freedom
I have found the problem, and as I suspected, it was in the function. the correct function is: (i still don't fully understand...

7달 전 | 0

질문

ODE45 Multiple Degrees of Freedom
Hi all, I am having difficulty in modelling a 3DOF system usng ODE45 as I am not getting the correct result. Therefore I woul...

7달 전 | 답변 수: 2 | 0

### 2

답변

질문

ode45 does not return the right answer for internal combusion engine pressure profile
Hi all, I have been getting plenty of practice the last few days with ODE45 and there is one problem I am trying to solve that...

8달 전 | 답변 수: 0 | 0

답변