문제를 풀었습니다


Back and Forth Rows
Given a number n, create an n-by-n matrix in which the integers from 1 to n^2 wind back and forth along the rows as shown in the...

7년 초과 전

문제를 풀었습니다


Sum all integers from 1 to 2^n
Given the number x, y must be the summation of all integers from 1 to 2^x. For instance if x=2 then y must be 1+2+3+4=10.

7년 초과 전

문제를 풀었습니다


Finding Perfect Squares
Given a vector of numbers, return true if one of the numbers is a square of one of the other numbers. Otherwise return false. E...

7년 초과 전

문제를 풀었습니다


find the Area of a rectangle
length is x width is y what is the area of the rectangle?

7년 초과 전

문제를 풀었습니다


Times 2 - START HERE
Try out this test problem first. Given the variable x as your input, multiply it by two and put the result in y. Examples:...

7년 초과 전

제출됨


Using MATLAB for Bearing Fault Analysis
Ball Bearings can have several faults, which result in different signals. This program shows this.

거의 8년 전 | 다운로드 수: 24 |

Thumbnail

제출됨


Pause a long MATLAB run with a simple click.
A simple way to pause a long simulation, to check progress, without expensive breakpoints or checks

거의 8년 전 | 다운로드 수: 5 |

Thumbnail

문제를 풀었습니다


Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...

8년 초과 전

문제를 풀었습니다


Model a simple pendulum
Model a simple pendulum of length 200cm with bob of mass 100g and plot the position in degrees. The pendulum starts at 30 degree...

8년 초과 전

문제를 풀었습니다


Produce a Fibonacci sequence
Construct a diagram that generates the Fibonacci sequence: 1, 1, 2, 3, 5, 8, 13, 21, 34.....up to 377 The Fibonacci sequ...

8년 초과 전

문제를 풀었습니다


Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...

8년 초과 전

문제를 풀었습니다


Model a falling body
An object is falling freely from a height of 22 meters under the force of gravity. <<http://blogs.mathworks.com/images/seth/c...

8년 초과 전

문제를 풀었습니다


Model a mass spring system
Model an ideal mass-spring system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/images/se...

8년 초과 전

문제를 풀었습니다


Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...

8년 초과 전

문제를 풀었습니다


Add damping to a mass spring system
Model an ideal mass-spring-damper system shown below where the spring is initially stretched. <<http://blogs.mathworks.com/im...

8년 초과 전

문제를 풀었습니다


Make a full wave rectifier
Produce a full wave rectifier waveform for the given sine wave source. For a sine wave input, the output of the full wave rec...

8년 초과 전

문제를 풀었습니다


Make a half wave rectifier
Produce a signal that outputs the given sine wave source when it is greater than zero and outputs zero when it is less than zero...

8년 초과 전

문제를 풀었습니다


Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>

8년 초과 전

문제를 풀었습니다


Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...

8년 초과 전

문제를 풀었습니다


Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...

8년 초과 전

문제를 풀었습니다


Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>

8년 초과 전

문제를 풀었습니다


Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...

8년 초과 전

제출됨


Designing a controller for an Inverted Pendulum - hebrew
Designing a controller for an Inverted Pendulum - hebrew

대략 10년 전 | 다운로드 수: 2 |

Thumbnail

제출됨


Using Simscape for design of Multi-Domain Physical Systems
Using Simscape for design of Multi-Domain Physical Systems

대략 10년 전 | 다운로드 수: 1 |

Thumbnail

제출됨


Using SimMechanics for designing and testing Mechanical Systems
A Presentation and demos for using Simulink, SolidWorks and SimMechanics.

대략 10년 전 | 다운로드 수: 3 |

Thumbnail

제출됨


Using Model-Predicite Control - Presentation and Recording - Hebrew
Using Model-Predictive Control (MPC) for Control Design

대략 10년 전 | 다운로드 수: 1 |

Thumbnail

제출됨


Converting Dataset Simulation results to Excel Spreadsheet
Two simple functions that convert a Dataset parameter, containing Simulink Simulation data, to excel

거의 11년 전 | 다운로드 수: 6 |

Thumbnail

제출됨


Comparing different methods to solve an Inverted Pendulum problem
A simple reporting tool that shows how you can model an inverted pendulum in a few methods.

대략 11년 전 | 다운로드 수: 3 |

Thumbnail

제출됨


Reporting tools in the MATLAB and Simulink Environment
This submission shows how you can export your results from MATLAB, via different reports.

대략 11년 전 | 다운로드 수: 2 |

Thumbnail

제출됨


Reporting tools in the MATLAB and Simulink Environment
Three ways to report your results to someone who doesn't use MATLAB.

대략 11년 전 | 다운로드 수: 2 |

Thumbnail

더 보기