Torsten Knodt
A123 Systems GmbH
Followers: 0 Following: 0
Professional Interests: Rapid Prototyping, Ground Vehicle Physical Simulation, Virtual Integration, Model Based Development, AutoSAR, Symbolic Solutions to Differential Equations, Static and Dynamic Parameter Estimation
Feeds
질문
How to continuously repeat the output of the "From Spreadsheet" source block?
Hi, How can I continuously repeat the output of the "From Spreadsheet" source block? The extrapolation at the end does not pro...
4년 초과 전 | 답변 수: 1 | 0
1
답변질문
How can I draw a mesh into a block mask/ icon?
Hello, I have a masked Simulink block. Now I want to draw a mesh into the icon. Unfortunately the mesh is drawn into an own w...
대략 7년 전 | 답변 수: 1 | 0
1
답변문제를 풀었습니다
Compute the step response of a DC motor
Compute the step response of a DC motor shown below <<http://blogs.mathworks.com/images/seth/cody/dc-motor.png>> The param...
7년 초과 전
문제를 풀었습니다
Counting pulses in a signal
Count the number of pulses that are the result of summing each pulse generator block. Pulse Generator blocks produce a recurr...
7년 초과 전
문제를 풀었습니다
Make a low pass filter
Make a first order low pass filter that will filter out the high frequency oscillations for the given input signal. The cut-off ...
7년 초과 전
답변 있음
Automotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...
Automotive problem - Counting and saving
This depends on your interface to write to the EEPROM. Normally you would count in your RAM and trigger writing to the EEPROM in...
7년 초과 전 | 0
문제를 풀었습니다
Add offset to a signal
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-offset-eqn.png>> You should see a downward...
7년 초과 전
문제를 풀었습니다
Produce a sine wave
Produce a sine wave with amplitude 3: <<http://blogs.mathworks.com/images/seth/cody/sine-eqn.png>>
7년 초과 전
문제를 풀었습니다
Produce a cosine wave
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/cosine-eqn.png>>
7년 초과 전
문제를 풀었습니다
Connect blocks in a model
Connect the blocks in the model to produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/connect-blocks...
7년 초과 전
문제를 풀었습니다
Add a block to a model
Produce the following signal: <<http://blogs.mathworks.com/images/seth/cody/add-block-eqn.png>> In this case, the slope of...
7년 초과 전
문제를 풀었습니다
Make the vector [1 2 3 4 5 6 7 8 9 10]
In MATLAB, you create a vector by enclosing the elements in square brackets like so: x = [1 2 3 4] Commas are optional, s...
7년 초과 전
문제를 풀었습니다
Pizza!
Given a circular pizza with radius _z_ and thickness _a_, return the pizza's volume. [ _z_ is first input argument.] Non-scor...
7년 초과 전
답변 있음
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...
How can i change a value of a resistor during simulation using simpowersystems toolbox ( R L C branch )
I had the same requirement. I either use a voltage measurement together with a controlled current source or a current measureme...
7년 초과 전 | 0
| 수락됨
질문
/usr/bin/ld: raccel_sfcn_utils.o: undefined reference to symbol 'dlclose@@GLIBC_2.2.5'
I get the following message when starting a simulation in rapid acceleration mode under Ubuntu Xenial 64 Bit which works under W...
7년 초과 전 | 답변 수: 0 | 0
0
답변질문
What is the cause of the error message "FIMATH mismatch:Property 'ProductWordLength'" here?
I get the error message FIMATH mismatch:Property 'ProductWordLength': 16 ~= 32 from the following action code in a stat...
7년 초과 전 | 답변 수: 0 | 0
0
답변답변 있음
How to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...
How to define the sampling time in a system of Simscape Power System Blocks without accuracy lost importants?
Hi Tony, it's hard to give an advice without knowing your model, simulation settings and the intent of your simulation. Becaus...
거의 8년 전 | 0
| 수락됨
질문
OutOfMemoryError when building PDF System Design Description for "big" Simulink Model
Hello, I get an OutOfMemoryError when building a System Design Description in PDF and Word format. I already increased the heap...
8년 초과 전 | 답변 수: 0 | 0
0
답변질문
Initial output value for bus in enabled subsystem hierarchy
I have a hierarchy of subsystems where a middle subsystem is an enabled one. The hierarchical subsystems each have a single outp...
9년 초과 전 | 답변 수: 1 | 0
1
답변질문
Analyzing and creating fixed-point data types.
Hello, is there a single function to get the minimum and maximum value representable by a specific fixed-point data type? I am ...
대략 11년 전 | 답변 수: 1 | 0
1
답변질문
Simulink message "Attempt to use invalid data type id 17"
Hello, how can I find out which data type corresponds to a specific id when getting the message "Attempt to use invalid data ty...
11년 초과 전 | 답변 수: 1 | 2
1
답변질문
"Variable time delay" block in "For Each Subsystem"
Hello, I try to synthesize noise coming from multiple targets to multiple sensors. I have two cascaded for-each sub-systems, th...
대략 12년 전 | 답변 수: 1 | 0