This example shows how to design octave-band and fractional octave-band filters. Octave-band and fractional-octave-band filters are commonly used in acoustics, for example, in noise control to perform spectral analysis. Acousticians prefer to work with octave or fractional (often 1/3) octave filter banks because it gives them a more meaningful measure of the noise power in different frequency bands.

**Design of a Full Octave-Band and a 1/3-Octave-Band Filter Banks**

An octave is the interval between two frequencies having a ratio of 2:1. An octave-band or fractional-octave-band filter is a bandpass filter determined by its center frequency and its order. The magnitude attenuation limits are defined in the ANSI® S1.11-2004 standard for three classes of filters: class 0, class 1 and class 2. Class 0 allow only +/-.15 dB of ripples in the passband while class 1 filters allow +/-.3 dB and class 2 filters allow +/-.5 dB. Levels of stopband attenuation vary from 60 to 75dB depending on the class of the filter.

Design a full octave-band filter bank:

BandsPerOctave = 1; N = 6; % Filter Order F0 = 1000; % Center Frequency (Hz) Fs = 48000; % Sampling Frequency (Hz) f = fdesign.octave(BandsPerOctave,'Class 1','N,F0',N,F0,Fs);

Get all the valid center frequencies in the audio range to design the filter bank:

F0 = validfrequencies(f); Nfc = length(F0); for i=1:Nfc, f.F0 = F0(i); Hd(i) = design(f,'butter'); end

Now design a 1/3-octave-band filter bank. Increase the order of each filter to 8:

f.BandsPerOctave = 3; f.FilterOrder = 8; F0 = validfrequencies(f); Nfc = length(F0); for i=1:Nfc, f.F0 = F0(i); Hd3(i) = design(f,'butter'); end

Visualize the magnitude response of the two filter banks. The 1/3-octave filter bank will provide a finer spectral analysis but at an increased cost since it requires 30 filters versus 10 for the full octave filter bank to cover the audio range [20 20000 Hz].

hfvt = fvtool(Hd,'FrequencyScale','log','color','white'); axis([0.01 24 -90 5]) title('Octave-Band Filter Bank') hfvt = fvtool(Hd3,'FrequencyScale','log','color','white'); axis([0.01 24 -90 5]) title('1/3-Octave-Band Filter Bank')

**Spectral Analysis of White Noise**

The human ear interprets loudness of sound on a scale much closer to a logarithmic scale than a linear one but a DFT-based frequency analysis leads to linear frequency scale. Compute the (DFT-based) power spectrum of a white noise signal using a spectrum analyzer:

Nx = 100000; SA = dsp.SpectrumAnalyzer('SpectralAverages',50,'SampleRate',Fs,... 'PlotAsTwoSidedSpectrum',false,'FrequencyScale','Log',... 'YLimits', [-80 20]); tic, while toc < 15 % Run for 15 seconds xw = randn(Nx,1); step(SA,xw); end

Now filter the white noise signal with the 1/3-octave filter bank and compute the average power at the output of each filter. While the power spectrum of a white noise signal is flat, the high frequencies are perceived louder. The 1/3-octave spectrum paints a picture that is closer to the human ear perception. It shows a spectrum where the power level rise 3dB per octave because each band (i.e. filter) has twice the frequency range of the preceding octave.

SA2 = dsp.SpectrumAnalyzer('SpectralAverages',50,'SampleRate',Fs,... 'PlotAsTwoSidedSpectrum',false,'FrequencyScale','Log',... 'RBWSource','Property','RBW',2000); yw = zeros(Nx,Nfc); tic, while toc < 15 % Run for 15 seconds xw = randn(Nx,1); for i=1:Nfc, yw(:,i) = filter(Hd3(i),xw); end step(SA2,yw); end

**Spectral Analysis of Pink Noise**

While a white noise signal has the same distribution of power for all frequencies, a pink noise signal has the same distribution of power for each octave, so the power between 0.5 Hz and 1 Hz is the same as between 5,000 Hz and 10,000 Hz.

Hpink = dsp.ColoredNoise(1,Nx,1); SA3 = dsp.SpectrumAnalyzer('SpectralAverages',50,'SampleRate',Fs,... 'PlotAsTwoSidedSpectrum',false,'FrequencyScale','Log',... 'YLimits', [-80 20]); tic, while toc < 15 % Run for 15 seconds x = step(Hpink); step(SA3,x); end

Now filter the pink noise signal with the 1/3-octave filter bank and compute the average power at the output of each filter. The power of the pink noise signal decline at higher frequencies at the rate of about -3dB per octave. However it sounds "constant" to the human hear and 1/3 octave-band spectrum shows flat at the output of the filter bank.

SA4 = dsp.SpectrumAnalyzer('SpectralAverages',50,'SampleRate',Fs,... 'PlotAsTwoSidedSpectrum',false,'FrequencyScale','Log',... 'RBWSource','Property','RBW',2000); y = zeros(Nx,Nfc); tic, while toc < 15 % Run for 15 seconds x = step(Hpink); for i=1:Nfc, y(:,i) = filter(Hd3(i),x); end step(SA4,y); end

Was this topic helpful?